Cam, stall, gear ratio question

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Joined
Jul 10, 2019
Messages
25
Reaction score
23
Location
Austin, Texas
In my 1995 4-door Tahoe I have modified the entire drivetrain and I would like some opinions on my choices. My main concern is the cam, stall, ring and pinon ratio combination, is my combo a good match for my purposes? Would there be a better combination? My purposes is that this Tahoe be a street car that is serious fun for cruising short distances, around town mainly, not a whole lot of highway driving. No track time but I do want to have as much power and acceleration on tap for the fun factor. I am not as concerned with mpg as I am smiles per-gallon. This vehicle is basically a toy that is driven a few times per week, not a daily driver. I want street drivability but mpg is not really important. Ok, here is what I have completed so far:
GM 350 Crate Engine Long Block #12568758 (2-Bolt Mains/One-Piece Rear Seal/9.25:1 Compression with 64cc Heads) - Installed 2016
Transmission: 4L60E - Rebuilt 2019
HGH Electronics Compu Shift 4L60 ECU
FTI Lock-Up Torque Converter (ESR3082): 9.5in./2800-3000RPM
TransGo HD2 Shift Kit/Corvette 2nd Gear Servo/Superior Billet 4th Gear Servo/Sonnax 3-4 Pinless Accumulator Piston
Richmond 4.56 Gears
Eaton TrueTrac
Edelbrock Pro Flo 4 EFI System (35770) 35 Lb/Hr Injectors (Can support up to 550hp at 58 psi.) Edelbrock Distributor/Ignition Coil
AEM Fuel Pump/Adjustable Fuel Pressure Regulator
MSD Street Fire Ignition Box/AC Delco Spark Plugs/Jegs 8.0 Wires
AFR 180 Fully Assembled Cylinder Heads (0918) 65cc Combustion Chamber Intake Valve Diameter: 2.020in. Exhaust Valve Diameter: 1.600in. Max Valve lift: .600in. (I am guessing the final compression ratio is approx. 9.1 and I always use 93 octane. I have never noticed any knocking or pinging.) Comp XFI268 Hydraulic Roller Cam DURATION: 218int./224exh. LIFT: .570int/.565exh (w/1.6) LSA: 113
COMP Hydraulic Roller Lifters/COMP OEM Style Installation Kit
COMP 1.6 High-Energy Die Cast Aluminum Roller Rocker Arms/Texas Speed Chromoly Pushrods RPC Mid-Length Headers/Flowmaster Y-Pipe/High-Flow Cat DynoMax Super Turbo 3in. Offset In/Out Muffler 17792/3in. Exhaust Tubing
K&N Air FIlter
Flex-Lite Dual Electric Fan Kit/Edelbrock Aluminum Water Pump/New Radiator/Underdrive Pully Kit
Wheels/Tires:
Front: Original OEM 16x7 General Grabber UHP 255/65R16
Rear: Original OEM 16x7 General Grabber UHP 255/65R16
I have also rebuilt/modified the suspension and brakes as well. I am quite happy with all I have done and the Tahoe is a blast to drive. The ProFlo 4 and AFR heads are amazing (there is a strong smell of gas when the engine is running that I haven't been able to pinpoint. The air fuel ratio and timing is perfect, perhaps it's the charcoal canister delete?). I just wonder if maybe a different combo would perform better for my purposes? What would you have done differently? I am welcoming all opinions and comments. Would a different cam or stall or gear ratio combo net me more acceleration on the street? I haven't had any dyno time but I do plan in the future to get a hub dyno session. Thanks!
 
Last edited:

RDF1

I'm Awesome
Joined
Apr 3, 2018
Messages
1,273
Reaction score
1,191
Location
MS
Can you try and lean it out at idle and see if that helps.
Ive never messed with that EFI system so not sure what all it has for options.
But Getting the compression up and going with a larger cam would be my advise. Especially since your already running 93 octane.
Didn't see Headers mentioned?
 

arrg

I'm Awesome
Joined
Apr 29, 2015
Messages
415
Reaction score
346
Location
Bay Area, CA
What does it not do now that you would like it to do after you throw more money at it? As for the fuel smell, where do you have your oxygen sensor? When I had mine in the driver's side header, I had the fuel smell problem, but when I moved it to the Y-pipe, most of it went away.
 
Joined
Jul 10, 2019
Messages
25
Reaction score
23
Location
Austin, Texas
What does it not do now that you would like it to do after you throw more money at it? As for the fuel smell, where do you have your oxygen sensor? When I had mine in the driver's side header, I had the fuel smell problem, but when I moved it to the Y-pipe, most of it went away.
My main question is what is your opinion of my cam/stall/gear ratio for my stated purposes? Is this the best combo for power and street drivability while not being concerned with mpg? What would you have done differently if anything?
The o2 sensor is located in the y-pipe, not the driver's side header collector. The gas smell is not too bad but it does smell rich. I have triple checked the air/fuel ratio and timing but that doesn't stop the smell. I will try the leaning out idea mentioned before, thanks!
 
Joined
Jul 10, 2019
Messages
25
Reaction score
23
Location
Austin, Texas
Can you try and lean it out at idle and see if that helps.
Ive never messed with that EFI system so not sure what all it has for options.
But Getting the compression up and going with a larger cam would be my advise. Especially since your already running 93 octane.
Didn't see Headers mentioned?
RPC mid-length headers. I really don't want to go with a larger cam. I feel this is the largest cam I want for drivability purposes. Same with compression. Thanks for the leaning out idea, I will try it :)
 

arrg

I'm Awesome
Joined
Apr 29, 2015
Messages
415
Reaction score
346
Location
Bay Area, CA
My main question is what is your opinion of my cam/stall/gear ratio for my stated purposes? Is this the best combo for power and street drivability while not being concerned with mpg? What would you have done differently if anything?
The o2 sensor is located in the y-pipe, not the driver's side header collector. The gas smell is not too bad but it does smell rich. I have triple checked the air/fuel ratio and timing but that doesn't stop the smell. I will try the leaning out idea mentioned before, thanks!
What do you have set for idle AFR and timing?
 

RDF1

I'm Awesome
Joined
Apr 3, 2018
Messages
1,273
Reaction score
1,191
Location
MS
RPC mid-length headers. I really don't want to go with a larger cam. I feel this is the largest cam I want for drivability purposes. Same with compression. Thanks for the leaning out idea, I will try it :)

It might sound odd, but you can try and richen it up also.
Ive tried leaning out a LS one time to kill the smell and it got worse. richened it up and it got alot better.

Also does it have a option of Injector timing?
If you can adjust when the injector fires where it hits a closed intake valve it will atomize and burn better plus kill the rich smell
 

LC2NLS6

I'm Awesome
Joined
Apr 23, 2019
Messages
277
Reaction score
235
Location
MI
What rpm are you shifting at? You have good heads, so it should run to 6000 easy with that cam I'd think. Get it dynoed and see what it does.
 

Erik the Awful

Truly Awesome
Air Force Supporting Member
Joined
Aug 9, 2019
Messages
10,035
Reaction score
23,505
Location
Choctaw, OK
I think your O2 sensor is too far back. I put mine a little too close in my header collector. Otherwise, I don't see anything glaringly wrong with your combination.
 

PlayingWithTBI

2022 Truck of the Year
Supporting Member
Joined
Jan 3, 2019
Messages
14,598
Reaction score
29,580
Location
Tonopah, AZ
I think your O2 sensor is too far back. I put mine a little too close in my header collector.
I don't know if your EFI has the capability, or table, where you can adjust the delay to compensate for the position of your O2 sensor. Usually if it's off you'll get stumbling because the ECM is adjusting to soon or late based on O2 feedback. Here's the table in the EBL. It's based on Gms/Sec.
You must be registered for see images attach


You must be registered for see images attach


Edit: for some reason I can't delete the 2nd snap shot, it's the same as the 1st.
 
Joined
Jul 10, 2019
Messages
25
Reaction score
23
Location
Austin, Texas
Thank you all for the tips on the O2 sensor and the rich smell, I will will be trying those out.

But honestly, I now wish I made a separate post about that. I am not so interested in the that issue as I am opinions on my cam, stall and rear gear ratio combination. Would you guys say that the specs of the cam are a decent match for the specs of the torque converter and rear gear ratio based upon my stated purposes? Keep in mind, my purposes are a balance of as much power and acceleration as possible WITH street drivability (while not being concerned with highway cruising and mpg). Is it too much stall for the cam or is it a good match up? I understand that there will be compromises to achieve these two conflicting goals but I am ok with that. This truck is not a track car or a daily driver. It is a fun machine for the street.
 
Last edited:

arrg

I'm Awesome
Joined
Apr 29, 2015
Messages
415
Reaction score
346
Location
Bay Area, CA
I have the same converter in my truck w/3.42 gears and a smaller (212/218) cam. With your combo, I can't see why you'd want less stall speed. I agree with LC2NLS6 though, your shift points should be somewhere near 6000 rpm for that combo.
 

Schurkey

For a pacifist, I sure am a radical mother...
Supporting Member
Joined
Jan 14, 2018
Messages
17,611
Reaction score
27,201
Location
The Seasonally Frozen Wastelands
My main concern is the cam, stall, ring and pinon ratio combination
GM 350 Crate Engine Long Block #12568758
"VIN K" stock replacement engine. Functionally the same as the original engine. Dished pistons, too deep "in the hole". Low compression. Crying out for thin head gaskets.

FTI Lock-Up Torque Converter (ESR3082): 9.5in./2800-3000RPM
I don't know this company or their products.

Cheap, mass-market "performance" torque converters are a disaster. A "good" performance converter is expensive; and drives like a stock converter at low- and part-throttle. If this converter slips a lot in normal driving, it's not one of the "good" ones.

Richmond 4.56 Gears
4.56 seems excessively deep; but that'll depend on your tire diameter.

MSD Street Fire Ignition Box
Good luck. MSD quality has taken a nose-dive; and their Street Fire line was always imported from Asia.

I wouldn't walk across the street for Street Fire products if they were giving them away for free. But you already have it, so until it dies there's no reason to change (assuming it has a reliable rev-limiter.)

AFR 180 Fully Assembled Cylinder Heads (0918) 65cc Combustion Chamber... ... (I am guessing the final compression ratio is approx. 9.1 and I always use 93 octane. I have never noticed any knocking or pinging.)
WHY are you using premium fuel in a nothing-to-one compression engine? This is crazy. You might actually get more power from lower octane. Won't be much of a difference, but it's possible. And less expensive.

What thickness are the head gaskets? Anything beyond .020 is too thick. .040-thick gaskets are common.

Comp XFI268 Hydraulic Roller Cam DURATION: 218int./224exh. LIFT: .570int/.565exh (w/1.6) LSA: 113
Nice, mild specs yet still far "bigger" than the original cam.

Might not have been my first choice, but it should work OK.
1. Was the cam degreed?
2. Is the distributor gear compatible with this cam?
3. Does this cam/lifters use the OEM thrust plate and dogbones?

COMP 1.6 High-Energy Die Cast Aluminum Roller Rocker Arms
Die-cast arms? Kinda scary.

But then, I'm so old that I remember when aluminum rocker arms had a 2,000-mile service life. When it's me, I buy steel roller rockers from Comp.

High-Flow Cat
New catalyst, and the exhaust still smells "rich"?

There's something wrong. Maybe several things. One wonders if the new catalyst has quit working. ("Murdered by misfire".)

Flex-Lite Dual Electric Fan Kit/Edelbrock Aluminum Water Pump/New Radiator/Underdrive Pully Kit
That's some serious downgrading of the cooling system.

Front: Original OEM 16x7 General Grabber UHP 255/65R16
Rear: Original OEM 16x7 General Grabber UHP 255/65R16
Axle ratio is too deep. You've got a mild engine with low compression ratio. It's not set up for high-rpm power, but you've got small-ish tires, deep gears, and higher stall speed. You're throwing away any low-rpm power, and not fully using midrange power. But, sure, it'll make the engine seem peppy.

(there is a strong smell of gas when the engine is running that I haven't been able to pinpoint. The air fuel ratio and timing is perfect,
1. Define "perfect" A/F, and "perfect" timing.
2. How are you measuring A/F ratio?
3. "Smelling fuel" in the exhaust? Often a sign of misfire. Can be rich misfire, can be lean misfire, can be misfire for ANY reason except a non-firing injector. Fix the misfire, the eye-watering "rich" smell goes away and the catalyst is much happier.

perhaps it's the charcoal canister delete?).
WHY would you do that???

If the "gas" smell isn't from the exhaust, this is a strong possibility.
 
Last edited:

CrustyJunker

Is STILL Here?
Joined
May 20, 2012
Messages
774
Reaction score
963
Location
Indiana, USA
Sounds like you have a pretty good combo as it is. All those parts will work well together (my opinion). A 4-door Tahoe is a reasonable size/weight that you've already compensated with gears and converter. 180cc heads are a great size for that cubic inch/cam size and keeping your torque up. Vacuum brakes probably still behave - also nice!

Even a smaller converter would've been fine for that combo...But you're right in the power range you need to be. I don't think there's anything really worth changing at this time.

Me thinks swapping cams, gears, converters, or head gaskets to bump up compression would give you marginal gains you'd only measure on a dyno (and be a lot of work).

You've covered all the weak points and cost-effective upgrades. Anything more - you'll want a whole new combo and a 4L80.

Happy truckin'! :driver:
 

Latest posts

Forum statistics

Threads
78,032
Messages
1,643,905
Members
81,075
Latest member
gmt400isking
Top