'98 Busurban Storm Chase Vehicle Build

[Jerryred94silvy]

When I do paint it, I might 2 tone it, so what color should the 2 tone be (Or should I leave it be)

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

Photos #1, 3 and 5 have my vote, with #3 being my top pick.

 

[jjester6000]

Here's another angle for the 2 tone.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[jjester6000]

I think I made my decision, I like the WA6270 Dark Argent Metallic as my secondary color.

You must be registered for see images attach

(I tweaked it so that the emblems pop a bit more).

 

[jjester6000]

You must be registered for see images attach

I got the mileage corrected, and even corrected the speedometer.

You must be registered for see images attach

Using a gps speedometer app, I set the cruise control, took the needle off, then clocked it where it should be, and now it reads totally accurate.

You must be registered for see images attach

I also replaced the broken drivers exterior door handle, and am about to install my CB.

You must be registered for see images attach

I'm very close to taking this thing chasing.

 

[jjester6000]

You must be registered for see images attach

Guess who has ice cold A/C now!!!

You must be registered for see images attach

I had to wire the compressor up to a toggle switch after charging it up, but it all worked out.

 

[jjester6000]

I'm going the Maaco route when it comes to painting the truck, but with a twist . . .

You must be registered for see images attach

I just got a job at me local Maaco doing paint prep!!!

You must be registered for see images attach

That means that I'm going to be able to have it painted for just the cost of materials. Anyways, I just started test fitting my new/used lower quarter. I would have had it welded last night, but I ran out of welding wire.

Sent from my IBM PS/2 Model 53 486SX using Tapatalk

 

[Jerryred94silvy]

I'm going the Maaco route when it comes to painting the truck, but with a twist . . .

You must be registered for see images attach

I just got a job at me local Maaco doing paint prep!!!

You must be registered for see images attach

That means that I'm going to be able to have it painted for just the cost of materials. Anyways, I just started test fitting my new/used lower quarter. I would have had it welded last night, but I ran out of welding wire.

Sent from my IBM PS/2 Model 53 486SX using Tapatalk

I’ll have my truck to you by next week to work your magic on it lol. But for real, new paint is exciting! This hoss is coming along nicely

 

[jjester6000]

I got it welded on there, and one coat of fiberglass filler with WAYYYYY too much hardener since it's like 40 degrees out right now.

You must be registered for see images attach

 

[jjester6000]

You must be registered for see images attach

So I sanded down that one coat of fiberglass, and sprayed some duplicolor over it, and well there it is.

You must be registered for see images attach

In my defense, it was dark, snowing, and I didn't have my glasses when I painted it. Of course this is only temporary, but it looks so ****** that I got to try again.

 

[Dariusz Salomon]

You must be registered for see images attach

We just picked up my buddies wrecked ranger.

You must be registered for see images attach

He hit a tree going 40 after someone pulled out in front of him.

You must be registered for see images attach

The Burb did a pretty good job pulling it.

You must be registered for see images attach

After resetting the fuel pump breaker, it started right up, but the frame is kinked between the bed and cab, so he's not going to fix it.

You must be registered for see images attach

Nice wheels on the ranger