nv3500

  1. 9

    NV3500 shift knob change

    Hi everyone. I have a ‘90 Scottsdale K2500 manual. Believe it’s an NV3500 as it doesn’t have a granny. Engine is the 350. I’m looking for the specific type of knob seen in the photo. In the picture it’s attached to a 1995 K2500. Anyone know where I can find this? I’ve read that changing...
  2. Tyler Campbell

    Nv3500 not engaging reverse switch

    Replaced the failed reverse switch in my 96 k1500 with a 5 speed manual transmission, but the reverse lights don't turn on unless I push the shifter to the passenger side firmly. What is the part in the transmission called that is worn, and can it be repaired/replaced without completely...
  3. A

    Does the nv3500 manual transmission have cooler lines?

    Hi I have a 1995 chevy k1500 short-bed stepside with the 305. It has a 5 speed which I believe is the nv3500. The previous owner had replaced the radiator with an aftermarket aluminum one and there are ports on the passenger side that I’ve seen automatic transmissions hooked up to, but mine...
  4. H

    5.0 manual trans swap bin file

    Since the trans in my stock 1995 c1500 with a 5.0 (305) died on me this morning, I have decided it is time to finally put in a manual. for this, I've decided to just go with a nv3500, (the truck is completely stock and makes very little power so I'm not too worried about strength). I can't find...
  5. A

    Making an external slave work with a Ls?

    Over the past few months I’ve been swapping an lq9 into my 95. Finally got to where I thought I was really close just to bolt up the trans and have the slave cylinder interfere with the oil pan. So now I’m at a crossroads, either swap in a 96+ nv3500, convert mine to internal, or go to a t56...
  6. Brantly

    Pilot Bearing Orientation

    I have a 98 1500 with the nv3500 and its been awhile since ive replaced the clutch including the pilot bearing, i was wondering whoch side of the bearing goes towards the engine? there doesnt seem to be a taper on either end thanks guys.
  7. 1

    What pedals would work best for my build? 1990 Chev nv3500

    Hey there , I have a 1990 chev 1500. I have been picking away at putting a nv3500 in it . I am wondering what pedals would be the easiest to use for my build ? And any more tips or suggestions? Reg cab , has auto brake pedal and gas pedal currently . Looks like hood latch cable and maybe fuse...
  8. A

    Transmission compatibility

    Will a NV3500 from a 2006 Chevy 1500 2wd, Fit a 98 Chevy C1500 2wd
  9. J

    Goodwrench nv3500

    So I recently purchased a 92 single cab z71 that was a 5 speed. Well I pulled it apart and upon further inspection I realized it’s a goodwrench replacement transmission. I was just wanting to know a little bit more info about them like how much there worth and and how much there capable of...
  10. Sprocket454ss

    clutch not disengaging (lm7 + hm290)

    My clutch is not disengaging when I press the pedal in. I did the nfw1050 flywheel and luke 4-201 clutch kit. I can row through all the gears when the truck is sitting still, pressing in the clutch helps a little bit with this. If I fire it up in first gear with the clutch pressed in (I may be...
  11. G

    Cheap fuel setup lm7 swap in 91' rcss

    I bought a brand new 96+ Vortec fuel pump and swapped it in from the weak tbi pump. I've done a lot of research on how to go from the stock fuel hard lines to the quick connects on my intake (with return). But with all an fittings added up I'm looking at $90+ just in fittings to go from the...
  12. E

    Nv3500 swap trouble

    I’ve got an nv3500 from a 91 c1500 2wD. I am currently undergoing a motor and auto to manual swap in my 1988 c1500. After putting in the transmission it slid in with no problem. After further inspection I was able to move the fork all the way back and all the way forward with no resistance. The...
  13. Thatguy0909

    Need Help Clutch Line Blowing Off

    I just replaced my whole clutch system due to my slave cylinder going out, now I cant get the clutch line to stay in the slave cylinder under pressure. Its a 1997 k1500 with the nv3500 in it. The slave cylinder has the metal clip but it also came with the plastic lock collar. Do I need to make...
Top