Just bought my 1st truck this weekend it’s a 95 k2500looking for a cheap set of good shorty headers, it’s a tbi 350 with an nv4500, im not sure if a mid length header would fit in these trucks or not, but eventually I’d like to build it into a 355
I’m sure this has been discussed before, but I see a lot of back and forth of arguing with header recommendations on the threads, LOL. Looking to purchase a set of long tube headers for my 5.7 vortec. I will be doing an EGR delete to broaden my choices for long tubes. Obviously I can’t narrow...
Ok not exactly, but it's definitely smaller than stock.
I'm the third owner of an 88 Chevy G20 van with a basically stock 350 (iron manifolds, factory y-pipe, cat, etc)
At some point the previous owner had the exhaust from the cat back replaced by someone who cobbled together such a goofed up...
hello, I’m new to the group but I read a lot on here, I’m trying to make my 94 Sierra k3500 more fuel efficient (I’m a comedian I know) it currently has a 454 TBI in it and is you’re typical dog. I know these aren’t race trucks but I want it to be able to hold its own. I also need to to...
88 k1500 5.7 with so many holes in my exhaust system from the y pipe down stream that I’m thinking of putting a new system on it.
My truck isn’t nice but the 350 can still sound decent without a bunch of leaks. So I’m looking for a cheapo system for a not great truck just to make it sound a...
Hello everyone, just bought a 97 single cab obs. Has a stock 305 (I plan on doing a 5.3 swap eventually), I want to put a black widow 250 or 300 on the truck. I’ve used the regular big boys (magna flows, flowmasters , and the 0$ option of open headers) but how does it sound on your truck? I...
I have a 89' C1500 have to replace the 350 that's currently in it do to a crack in the back of the block I found while I was about to change the clutch. Ordered a stock crate from JEGS and while I'm there should probably go ahead and do something with the headers. Don't really want to mess with...
Hey all, I'm new to the forums here. I have a 1998 K2500 with the 7.4L and 4L80e. Currently all it has is a CAI, true dual cat-back 2 1/4" straight pipes, and a custom 93 octane tune that was live-tuned using HPtuners. The exhaust is raspy as can be and I'm about tired of it (it was like that...
Hey guys, I'm going to be putting a 6.0L in my my 98 K1500 this summer and I'm trying to sort out the exhaust.
I'll be using stock manifolds, the guy building the engine said they flow great and I'm planning on a turbo in the future so dont want to waste money on headers.
My problem is what to...
My truck is a 1998 K1500 5.7L, currently has stock exhaust down to the rear cats. I had to chop off the mufflers the other day because one of them blew in half, and they were both rattling. When I dropped the tailpipes to the floor a bunch of the catalyst material fell out of the mufflers, so...
Texas
1988-1998
C1500 ls swap 3" exhaust
You will need own sensors
Local Pickup, or make shipping arrangements
I have a set up that I no longer need.
Schoenfeld ls1 swap long tubes 3" - mild steel
to 3" y merger
to 3" electric cut out and side dump
to 3" cat
to 3" flowmaster mild steel
to dump...
I have a 1996 Chevy K1500 with a 350. I plan on upgrading the exhaust soon on it. I want something that is loud and powerful, but not to the point where it is annoying to drive for longer than an hour. What do you guys recommend? I’m open to anything as long as it will still pass state safety...
Can y'all give me y'alls opinion on the best exhaust from headers to tips to make my v6 sound decent and keep it budget friendly I'm in high school with little money for the truck.
(1992 c1500 rwd swb with a 4.3 v6 completely stock.)
I have a 1993 Chevy K1500 ext. cab short bed and want to know if anyone can suggest a good complete exhaust system from the headers back with no cats and true dual if possible? I want something that will breath really well, especially after I stroke the current 350 to a 383.
Thanks!
Hi i have been looking all over to find some headers but all i can find are ones for two wheel drive if any one has any links to headers they have used on this setup please post the link thanks
I have a 95 5.7L, and I'm looking for an exhaust that will give me a loud but not too loud nice deep rumble without any pops or crackling sounds. I hear so many trucks in my town that sound like this, anyone know the setup to achieve this sound? Any input is appreciated, this is my first time...