I know what you are thinking by the thread title... "It's your ABS sensor my guy..."
But hear me out.
I bought the truck with the ABS light on, then I changed both sensors up front. ABS light went away. Great!
Now, on rare occasions... at low speed... the brake pedal, once depressed...
Vehicle: 1995 C2500 (8600gvwr) with 4WAL.
Issue: Air trapped in ABS module, cannot bleed via scanner (Snap-On Solus Pro with ver. 17.2 software), DTCs present, can't bleed with DTC's present, scanner displays 0 codes, jumping terminals A & H displays codes.
Codes:
Code 68 - Locked motor or...
I've got a 97 k1500 silverado, my abs went out so I deleted it with a proportioning valve. I did everything right, no leaks, brakes work great, don't have a spongey pedal anymore, but at a red light it's as if I'm pushing the gas pedal, I have to put all my weight on the brake pedal and the...
Hello!
1996 2 Door 4x4 Tahoe 5.7 300k Miles
Dash ABS light illuminated upon Key on and never cycles off.
I am unable to retrieve codes because my Scan tool is not seeing my ABS Module. I have used 2 different tools so far. Innova 3100 ABS and yesterday the Autel MX808. Neither can see the ABS...
All, first forgive the long post and please bear w/ me.
My truck: 1997 K1500 Z71, 3 door, 141" wheelbase, 5.7L, VIN (2GCEK19RXV1207157).
Me: beginning to think I'm an idiot, I'm definitely green behind the ears and could certainly use a well thought out explanation I can follow.
Doing my front...
abs fault? my 95 6.5TD Yukon came from the mechanic after bunch of stuff replaced including front wheel hubs all the brakes After we Got it the transmission was slipping to 1st and the speedometer dies happed every hard braking and started to happen every time i was braking and had to start the...
1994 Chevy full-size blazer (5.7 tbi OBD1).
Recently did the nbs master cylinder upgrade. Grabbed a mc out of 2001 Tahoe with vacuum booster.
After installing, bled the brakes and it is terribly squishy, worse than before. Dangerous lack of brake power. Was going to bleed again. But thought I’d...
Hey all!
I’ve got a 1996 Silverado k1500 with manual tranny and the 5.7TBI. Woke up this morning to a dead battery. Jumped it, truck ran fine. When I got in, ABS light was on and it wouldn’t go into 4x4. Normally not a huge deal, but we live in a hill and got a snow/ice storm last night Any...
So around 2 years ago I realized my parking brake wasn't holding my 98 K1500 in place when parked on a mild grade. She's an auto and I never use it but brakes is brakes and I don't skimp on safety. Ended up becoming a front to back brake job. Literally the only thing that didn't get replaced at...
98 Chevy K1500
About a year ago now I replaced a few things including my brake lights/turn signals/reverse lights to LED and doing a brake job all around. I've heard things about the LED's causing issues with cruise control and turning on the ABS light which I have both going on. I just want to...
I've got a 99 Tahoe LT 4wd 4dr with 4 wheel antilock brakes (currently not working).
When I press the brake pedal, nothing happens until the very end when the brakes grab violently. At low speeds my passenger rear wheel locks up.
I went on Identifix and they say it's either a BPMV (Brake...
Hello everyone! I just joined and have a question for anyone who can assist.
I have an OBS 2000 K2500 5.7L Vin R crew cab 4x4.
I am having trouble getting my OBDII to connect (there is power) and provide me with codes for a check engine light. I took it into the Chevy dealer and they have been...
Hello everyone, im sure this has been asked a few times but i can't seem to get the ABS and Brake light to go out. i have a 1992 2dr Blazer 4x4. brakes seem to work okay but when i went off road (and buried it) once i got it back home i cleaned everything up and since then the lights have...
Brake system is a JB7. Truck is 2000 K2500. So after doing some poking around I've seen a lot of info for pre-94 trucks removing ABS since they have a different system. On the trucks with the K-H ABS module, if I remove the ABS system is there anyway to do it where the light won't come on? Also...
I absolutely cannot find a part number, name for, or where to get a replacement for the rubber cap that goes on the high pressure accumulator bleeder valve...
Does anyone know or can find the part number? Know where I can get one? I absolutely cannot find it after doing a brake bleed.
A few months back I purchased a 1995 GMC Yukon dirt cheap,and today while changing out some bulbs in my cluster i realized a previous owner (prolly the shady used car lot my buddy bought the truck from) had removed the abs light. I installed a new light and wouldnt ya know it there was a reason...
I've been struggling to sort out the ABS in my 1998 K2500 since I bought it. At this point I'm stumped. Current situation is as follows:
Speedo works fine.
ABS light and C0236 code are triggered as soon as brakes are applied after moving (<20mph).
ABS does not function and rear wheels lock up...
1998 K2500 ECSB has had a code C0236 (missing rear speed sensor) since purchased.
I disassembled the wiring harness to look for a short and revealed that the wires from the rear speed sensor on the transfer case output terminated at another connector with a female to female adapter about 18"...
1998 K2500 ECSB has had a code C0236 (missing rear speed sensor) since purchased.
I disassembled the wiring harness to look for a short and revealed that the wires from the rear speed sensor on the transfer case output terminated at another connector with a female to female adapter about 18"...