Search results

  1. woody31

    oil pressure

    cam bearings are not aligned properly in the block,,
  2. woody31

    timing cover?

    the pushrods from the old block will work with the heads, and run roller tip self aligning rockers for a few more ponies..
  3. woody31

    Will a CEL come on......

    bad map sensor,,or a vacuum leak at the map sensor...located by the egr valve,,
  4. woody31

    High miles

    well i suppose mine is not even broke in yet,,1988 5.7tbi with only 142235 miles,,
  5. woody31

    vortec 350 carb conversion, say what!

    yes^^^
  6. woody31

    setting distributor (cam retard) on 5.7 vortec with aftermarket distributor

    elongate hole and be done with it,,
  7. woody31

    Exploding headlight bulbs.

    your lens is letting in moisture,,look for a crack or possible broken seal between lens and housing
  8. woody31

    audio upgrade---

    dude ,,get a life,,it was wrong plain and simple,,
  9. woody31

    What yr Tahoe?

    thanks guys,,this is my first venture into this body style, ill find one ,
  10. woody31

    What yr Tahoe?

    In other words. I'm looking for a 2 door tahoe. What yr is a good choice?
  11. woody31

    What yr Tahoe?

    Hey yall. i have a i\?? what yr tahoe is a good choice,,im looking for 96 % up with the 5.7 late model vortec. prefer 2wd, what yr and option sto look for and what to steer clear of??? thanks in advance.
  12. woody31

    Which harmonic balancer?

    hi scruf,,no difference in the pulleys,,both will bolt up, depends on what set up you go with, make sure you use the correct timing chain cover with the corresponding balancer or you will never be able to set the timing correctly. I would use the 95 balancer and cover and bolt serpintine pulley...
  13. woody31

    Skylark's dually

    nice ride^^
  14. woody31

    Hard Start in 96 454. Please Help, this is a doozy

    i still have my money on timing chain,,carry on,,,
  15. woody31

    Brake issue after 14b sf swap

    Did you keep the axles when you swapped in the 14th or did you use the originals from the 14b.? Sounds like a balance issue between the drum and axles. .As for the lock up pr9blem..could be adjusted to tight or the shoes are dirty or contaminated. .turn the drums also. .no matter what you do.
  16. woody31

    Hard Start in 96 454. Please Help, this is a doozy

    if the timing gear ,,looks ok,,i will throw this at ya....timing chain slop,,will cause all the symptoms you describe,,factory sets are horrible compared to a cloyes or equal quality set,,good luck..
  17. woody31

    Project: Mighty S10

    Swap the 2 plug in connections on top of the injectors. I had a issue one time where they got swapped around..motor would start but ran horrible.
  18. woody31

    power steering fluid leaking

    They can be resealed..but from my past experience with this. .it is a major pita. Time for a trip to pick n pull.. or a reman from your builder of choice.
  19. woody31

    No Oil Pressure

    I don't think they prime like a normal small block..I would put it all together and fire it up..good luck.
  20. woody31

    Glad to be here

    welcome to the site,,,enjoy
  21. woody31

    New from Texas

    Another welcome form Texas, where bouts you at?I am in the tyler area,,
  22. woody31

    I need this in my life

    For the amount of time and fabrication involved, that is a steal.
  23. woody31

    first modification suggestions

    Thanks for all the tips and posts,,looks like it is gonna be a flow master 40 series dumped at the rear end and a k&n air filter for a few ponies. I plan on a big cubic inch small block in the future with a th400 and low gears in the 14 bolt, slicks and maybe a 100 shot, that will start in the...
  24. woody31

    PROJECT: BARN FIND

    Thanks GW, Actually I think it is the roller pin, it snapped off. The door does not sag and it opens and shuts ok. Is it best to remove the door to attempt this??? thanks
  25. woody31

    PROJECT: BARN FIND

    uhh,,, yea ,, ill get right on that,,lmao

Latest posts

Members online

Total: 1,574 (members: 18, guests: 1,556)

Forum statistics

Threads
64,334
Messages
1,391,489
Members
51,439
Latest member
sherberto

Share this page

Top