Search results

  1. BuiltToWork

    Found/closed Full set of Pulley Mounting Brackets 1990 454 K3500 (PS pump, ALT, idler, air pump)

    This spring finally getting around to rebuilding the truck, someone hacked the whole front end pulley system. Looking to start over, correctly. I am not near a junkyard (Stafford, VA) that I know of. Can drive ~100 miles in my other truck to pick up parts. Want: Driveshaft pulley Fan clutch...
  2. BuiltToWork

    MORGAN AURORA 88 Rebuild

    I scored an old vice from my buddy for a case of beer. It's a Morgan Aurora 88. You Tubed it and apparently Morgan moved shop to Aurora sometime in the 70's ish. Before being bought by Milwaukee. It is useable, but in rough shape - but with some searching garagejournal forum and google, I was...
  3. BuiltToWork

    How Many Miles Do You Think My Truck Has Based On This Picture

    The Odometer stopped working at 75,123. Based on seat condition, how many real miles do you think it has? 1990 K3500 Flatbed I started pulling the dash, that's why it looks like that.
  4. BuiltToWork

    How to Mothball my project Truck - (Question)

    So, bought a project truck, 1990 K3500 454 Flatbed Dually. Ran when parked. It sat for two years in Wyoming, wouldn't start, had it shipped to VA as in-op. Got it in my yard, sat for another year. Fixed the ECU (water damage), ran good enough to get it to the shed. Started...
  5. BuiltToWork

    Sum Ting Wong

    Starting to fix up my farm truck (1990 K3500 454) and have bought the shop manual(s). I couldn't find the diagram in the manual matching my current set up. Searched this website and found a service manual that includes RVs and that looks similar to how mine is set up. I suspect someone...
  6. BuiltToWork

    Easy Flatbed Removal - How?

    I'm still prepping my Farm truck for the body off "restore". Is there a slick way to remove the heavy flatbed by myself? Unbolting it, is not the issue, pulling it from the frame and putting it back on is. I'm thinking of backing it back out of the shed onto a platform made of scrap wood, just...
  7. BuiltToWork

    Question: How to get at the ECM

    I'm trying to swap out my ECM, and have the new part in hand. I took the glove box out and can see the ECM but can't figure out how it's bolted in. Am I going to have to remove the whole dash? Trying to avoid that if possible. 1990 K3500 454 TBI Below is a pic of the frustratingly close ECM.
  8. BuiltToWork

    Rebuild - But not Restore, K3500 Farm Truck

    42 My plan for years was to get a hard working Truck and rebuild it from the ground up. Being Slightly OCD, I laid forth a plan. Truth Table: Buy A house with Acreage CHECK - 2 Acres (not a farm, but close enough) House has to have a detached Garage in the North 40 CHECK - See Pic below...
  9. BuiltToWork

    Use In Tank Fuel Pump to drain Tank - Good or Bad idea

    So my truck has been sitting for a year with a quarter tank of gas, no stabilizer. I traced the starting issue back to the ECM, which got wet. New ECM should be here today, but I don't want to install it until I know I can drive it under it's own power to my work shed. To drive it, I am...
  10. BuiltToWork

    ECM - Difference between EM7747 and EM8747

    I have an 1990 K3500 Auto 454 and suspect the ECM is bad. Looked up the part numbers and these two come up: EM7747 and EM8747 Took a picture of my ECM EM8747 but am curious if anyone knows the difference between the two. My guess: A/C control or Federal Smog or Man Trans vs Auto Trans.
  11. BuiltToWork

    The Three Sea Shells - What is this Relay?

    I have Three Relays in a row on my firewall and I have identified One (1) as the fuel pump relay. Any thoughts on what the other two are?
  12. BuiltToWork

    BW1370 or BW4401 Pic identification

    Not sure what Xfer case I have, I think it is a BW1370 or it might be a BW4401 1990 K3500 Pics below, please don't make me go out and take more - it's freezing cold and I don't want to wiggle on my back in the grass to get better pictures- ha ha
  13. BuiltToWork

    RPO Codes - Reverse Engineer

    I bought the truck very well used and I can't find any RPO codes except for a small placard on the fire wall. Doing Research I started re-building the factory original RPO list and this is what I have come up with so far: (might be wrong on a couple) (Also - I can't figure out the FLR code)...
  14. BuiltToWork

    New to GMT400 - 1990 K3500 Flatbed

    Hello all, New to Chevy Trucks - bought a 1990 K3500 Flatbed in Wyoming a year ago and finally had it shipped to Virginia. Some specs I think I figured out on it (not entirely sure): 10 1/2" Rear Dif 9 1/4 Front Dif Borg Warner 1370 XFER (not sure) Other stuff: 454 Automatic Flatbed with 5th...

Latest posts

Staff online

Members online

... and 7 more.
Total: 1,559 (members: 57, guests: 1,502)

Forum statistics

Threads
64,249
Messages
1,389,860
Members
51,240
Latest member
Baelfor

Share this page

Top