Search results

  1. E

    46mm Bored TBI Fuel Regular etc

    Have a tbi setup off my 95 k1500 with a 383 with less then 1000 miles on everything. Bored tbi, new injectors, adjustable fuel pressure regulator set to 18 psi, adapter plate to intake, sensors etc. $150 for everything you pay shipping. Located in canton CT.
  2. E

    89 C1500 LQ9 4L80 Speedomoter

    Hey all, I'm finishing up a engine swap on my 1989 C1500. Was originally a 4.3 auto, now 6.0 4l80. Everything works but I can't seem to get the speedometer to work and it did function before the swap. Tried splicing the original vss Purple and yellow wires to the vss output of the trans with...
  3. E

    99 Denali Overdrive Surge

    I have a 99 gmc yukon 5.7l. Starts runs and seems to drive great until it goes in overdrive. Once I get TC lockup I get a 200 rpm surge as if it were to come out of lockup and then rite back in. I can't really feel it but can hear it with the increased engine speed. Does this whenever...
  4. E

    99 Denali rear door latch

    Recently bought a 99 yukon without the drivers rear door operating. Finally got a chance to look into it and removed the door panel from the door and tried operating the linkage by hand and I cannot get the dang door to open! Tried locking and unlocking the door and i can see the lock...
  5. E

    Denali Fuel Pressure Low

    So as alot of you have seen i bought a 99 Denali with a bunch of electrical questions. I have not run it since I bought it and today was the first. Had low fuel pressure from the start 10 psi max. Replaced the fuel pump, same. Fuel filter replaced, same, relay same... said the hell with it...
  6. E

    99 Denali Alarm

    have a 99 Denali that has alarm issues. Alarm goes off every time you open the door with ot unlocked. Cycle the key and it stops.. PO pulled the horn fuse, now I know why!
  7. E

    99 Denali data port

    picked up a 99 gmc denail needing work. Went and bought a key fob for it as there was not one and when I went to jump the number 4 and 8 pin on the data port I found there is no number 8 pin! What now, is this an odd year, am i missing something or has someone messed with the wiring?
  8. E

    95 Engine Bay Diagram

    I'm in the process of removing my engine bay harness to get rid if all the Tbi, 4x4 and abs crap. Those items are no longer needed since I SASed it and am installing sniper EFI. I need the engine component wiring diagram to my truck to help me figure out what I can and cannot remove. Anyone...
  9. E

    95 Chevy 383 Timing

    I have a 95 k1500 with a HT383. Has 1 6 rockers and adaptor plate to a bored tbi. Trying to figure out what to set my base timing to. I have a hesitation when revving it up and has a bad ping with low throttle and heavy load. I got a chip from tbichips but he is unable to give me a for sure...
  10. E

    95 TBI 383 to Holley EFI

    What's everyone using for aftermarket fuel injection that is self tuning? My 95 is now 25 years old making it emissions exempt! I've been looking at the self tuning Holley setups and also thg he fast setups. What is better and why? I have a 383 that I built about 5 years ago with as bored...
  11. E

    NV4500 internal to external

    I got a 2000 nv4500 out of a gmc 3500. It's the internal throw out bearing. I'm putting it in my 95 with an external. Has anyone converted a internal style to a external? I can get a external bell housing fairly easily.
  12. E

    383 TBI Tuning

    I recently swaped out my 230K mile 350 with a 383 with vortec heads. I put the same parts in it as a HT383 the GM offers. I am running a edelbrock performer and adaptor plate with my factory 350 tbi. It seems to run very rich even with the factory chip. Specs, 95 chevy 1500 5speed 4X4 Fuel...
  13. E

    New Engine in No Clutch

    Hey all, finally got the 383 in the truck last night but when I went to try the clutch it would not disengage. Has a fairly light pedal and I can see the slave cylinder doing it's job but it's just not disengageing. It's a new Hays clutch, throw out bearing, pilot and new flywheel. Any ideas?
  14. E

    New Crossmembers After SAS

    To all you SAS guys! What kind of crossmembers you guys make for your trucks after cutting out the old ifs one? I did the conversion 2 years ago and just pulled the motor to replace with a 383 so I decided to cut out the old and make it look nice. I have one in the front going from the two...
  15. E

    Good Quality Clutch That Wont Brake the Bank

    Hey all what's a good clutch replacement for a 95 k1500 pickup? It's going behind a healthy 383 stroker with a nv3500. Should I get a stock replacement or a performance one?
  16. E

    383 Stroker No Oil To Most Rockers

    hey all, I finally finished my 33 stroker build for my truck. I went to prime the oil system but I am only getting oil out of cylinders 378 at the rockers.unfortunately I already installed intake manifold so I can't pull that off to see if I have oil leaking past the lifters. Any ideas before I...
  17. E

    Engine Compartment light

    Hey guys, on my 95 Chevy my engine compartment light flickers if I hit a bump with the hood closed so I unplugged it from the harness temporally. Now Ide like to figure out why it's not working properly so I traced the wires and I didn't find a switch to turn it on and off. What controls the...
  18. E

    The 95 Stepside Build

    So I think it's about time I make a build thread of my truck. Here's how I bought it over 8 years ago as my first truck. Bought it for 1200$ with a blown rear end. Not a spot of rust but was a masons work truck so the body was beat.
  19. E

    brake line size

    I need to replace the brake lines going from the master to the abs on a 97 Tahoe. Anyone know if there is a pre bent line from a store? Or what size is it for the front brake line from master to the abs.
  20. E

    reviving old carpet

    How to revive old matted down carpet. All I can think of is a brush with hot soapy water. I don't have a carpet cleaner but is there and around the house tools I could use to fluff it back up??
  21. E

    back seat for 2 door tahoe

    I bought a 2 door Tahoe with a trashed rear seat. Can't find any 2 doors for parts around here would a third row seat from a suburban work?
  22. E

    WRIST PINS DO NOT FIT!

    hey guys, so ive been working on my stroker finally and started putting the rods and pistons together (which are free floating pins). the first one i did went together fine, the fine spins freely and the rod floats as it should. All seven of the others not so much. the pins all fit properly...
  23. E

    383 stroker build

    Hey all I've been slowly gathering parts together for a 383 stroker. As of now I have a vortec small block 350 in the machine shop, an eagle 383 rotating assembly, and edelbrock e-tec 200 heads and a edelbrock performer intake that I'm going to run an adapter plate to me 670 cfm throttle body...
  24. E

    what diesel injectors

    so I just recently picked up a 2 door Tahoe with the 65 diesel.the truck was not running when I bought it so I ended up changing the fuel filter on it and got it running.at the bottom of the fuel filter housing was full of debris dirt particles so I'm thinking some of the injectors are clogged...
  25. E

    Picked up a new toy

    so I picked up a new toy this weekend. it is a 1997 2 door Chevy Tahoe. It has a 6.5 liter turbo diesel engine. the guy was selling on Craigslist for a thousand bucks. When to take a look at it the body is in rough condition but the frame is immaculate.it was so cheap because it did not run.I...

Latest posts

Members online

... and 13 more.
Total: 1,993 (members: 63, guests: 1,930)

Forum statistics

Threads
64,343
Messages
1,391,700
Members
51,456
Latest member
A_larios

Share this page

Top