Search results

  1. 1

    Keep your OBS

    ...bought mine new in 1996. still have it. and always will...
  2. 1

    96 Impala SS wheels advice?

    ...again, this was only on the front fitment. the rears were not an issue. they snugged right up. i also want to mention that on my front, i have 2'' drop spindles. now going to do 1 or 2" springs up there. I also don't care about the speedo being "off" a couple miles per hour. could care less...
  3. 1

    96 Impala SS wheels advice?

    ...all i can say is...on thinking back...is that your brake rotors center outside diameter must be a hair smaller in diameter than mine were/are. can't recall for sure, but i believe i replaced my brake rotors during a front brake job. they were just new stock size rotors, nothing fancy, but...
  4. 1

    96 Impala SS wheels advice?

    so i thought i was all done with the back of the wheel, hole size wise. the rears bolted up no problem. the fronts still had a minor rocking back & forth center hub too small issue. again, it was minor. so i put a very small rounding-over radius bit in the same router and removed the edge of the...
  5. 1

    96 Impala SS wheels advice?

    the ss wheels bolt right on to our c1500 trucks with only minor mods. first i used a straight small router bit on a router, to take off the very minor aluminum lip, that is on the backside centers of the wheels, so that all four wheels could be bolted onto any of the four corners of the truck in...
  6. 1

    96 Impala SS wheels advice?

    just installed a set of impala ss wheels that i restored, on my '96 shortbed. its currently lowered 6'' in the rear, and only 2'' in the front, but will be lowering the front a bit more, of course. standard diameter tires, the trucks came with, were 28 inch. i wanted to fill the wheelwells...
  7. 1

    ***** Any 2" / 4" lowers trucks out there???? ******

    ...still REALLY like this setup. 2-4 drop i believe...
  8. 1

    Best lowering option

    ...I like this outfit. They cost a bit more, but I like their stuff better than all the other usual places. On their site they answer the old question of whether or not so & so's spindles push your tires out or not, and how much. Like their regular C-notches & their taller C-notches...and...
  9. 1

    WTB hood.

    i needed a hood a couple years back. went to about six bone yards. they all had multiple hoods at fair prices. they were all already sorted & organized. one place had about 12 decent looking hoods, some with small dents, but otherwize they could be reconditioned & used. i lifted & looked at alot...
  10. 1

    Post pics of your truck with newer style factory oem wheels

    ...sewlow...really like the blue truck you had with the impala ss wheels. have the same truck. can you please tell me what size tires you had & what drop, if you can remember. thank-you very much!...
  11. 1

    95 C1500 build! Dropped, LS swap, paint!

    ...four years on, came across this thread. my compliments sir. truck really, really turned out nice!...
  12. 1

    SRT10 Replica wheels

    bought 4 new impala ss brushed center caps off ebay for $45.00 shipped. then buy whatever stickon center cap sticker emblems for them of your liking.
  13. 1

    SRT10 Replica wheels

    the bolt pattern IS the same from the impala ss to the gmt400 2 wheel drive. they are both 5 x 5. the trucks wheel studs are a hair larger in diameter, but they slide right on & bolt right up using the regular acorn lug nuts. the center hole needs to be routered out ever so slightly with a...
  14. 1

    ***** Any 2" / 4" lowers trucks out there???? ******

    ...Nice Impala SS wheel setup sewlow. They look great. What tires sizes please? Did you have to roll or cut the fender lips at all? Thanks
  15. 1

    OBS Camber/Caster Knock-outs - how to tell if you have them.

    if you never alter or change the ride height from standard, you will most probably never need to install the aftermarket offset camber bolts in question. people that lower their C-1500's need them, for example. very common.
  16. 1

    Belltech notch gap

    no, not really. you weld a bit at a time here & there.
  17. 1

    My 98 C1500 Short Box Rebuild

    ...do a 2/4 drop. and when you remove & replace the front spring perches, DO NOT THROW THEM OUT. keep them. they are valuable later, when you or someone else would then like to go to a 6'' back drop by doing an axle flip, as those stock original front perches are needed to go to a 6'' drop. yes...
  18. 1

    Belltech notch gap

    with all that being said, knowing what I know now, I will always both bolt, AND weld my C-notches in place...
  19. 1

    Belltech notch gap

    without giving belltech any ideas or solutions when you call, ask them what they suggest happened & what THEIR solution would be. just curious. if they say, well...frame sizes vary, say every one you've ever seen has the same issue, so what gives?
  20. 1

    Swap Meet Slam

    great write up. another obs saved & properly outfitted. May I ask what spare tire/wheel you finally went with? Am looking for a narrower than stock/original spare, a space-saver type, so to speak. thanks
  21. 1

    OBS Camber/Caster Knock-outs - how to tell if you have them.

    ...bringing a good thread forward into modern society...:D
  22. 1

    Upper Control Arm "Knock Out's" Question?

    ...They look like these guys...So one pair of these PER A-arm, correct?
  23. 1

    Upper Control Arm "Knock Out's" Question?

    ...then...question number two? lol ...whats the best to reach those damn bolts to adjust them? tire on, or off, or what? thanx again.
  24. 1

    Upper Control Arm "Knock Out's" Question?

    Knock-outs are out, now...do you install "two" of the new special eccentric bolt/washer jobs in each upper a-arm, or just one? one "pair" of them per a-arm, right? thanx
  25. 1

    Need help with upper control arm problems.

    general question: when you punch out the "knockouts" for the upper control arms & buy the encentric bolts that are needed for the extra camber they provide, do you buy & install two of those bolts per upper a-arm, or just one per side? thanx
Top