Search results
-
96 wont start after big tune up
Did you attach the ground to the back of the passenger side head? Wheres the rotor pointing towards? Did you plug in the distributor? Sent from my iPhone using Tapatalk- BadBowtie 98
- Post #8
- Forum: Feedback, Help and Suggestions
-
New tools!
The harbor freight one is pretty nice, and it’s built well enough that you can use it as a ratchet. Sent from my iPhone using Tapatalk- BadBowtie 98
- Post #24
- Forum: The Garage
-
Battery Drain :(
So it looks like it's something with the fuse block then?- BadBowtie 98
- Post #3
- Forum: Audio + Electronics
-
Battery Drain :(
I have a battery drain that's been plaguing me for a while... It's around a 1 amp draw using a DVOM When I remove the IGN Fuse and The Battery fuse it drops down to 0.1amp draw so I know it's coming from those circuits Anybody know what I should be looking for? What circuits are even on the...- BadBowtie 98
- Thread
- Replies: 3
- Forum: Audio + Electronics
-
First Project Truck!! 1998 Z71
Nice build, I'm in Tallmadge.- BadBowtie 98
- Post #83
- Forum: Member Trucks
-
BadBowtie 98 Build Thread
I'll have to try and see if one of them will do it for me. Got the sway bar set up today, was able to use the stock location. Just had to weld some tabs onto the axle.- BadBowtie 98
- Post #590
- Forum: Member Trucks
-
BadBowtie 98 Build Thread
I'm working on figuring one out- BadBowtie 98
- Post #587
- Forum: Member Trucks
-
BadBowtie 98 Build Thread
Still no front drive shaft, but I do have shocks now!- BadBowtie 98
- Post #584
- Forum: Member Trucks
-
88GMCtruck's never ending 88 GMC build thread
It's so beautiful- BadBowtie 98
- Post #408
- Forum: Member Trucks
-
88GMCtruck's never ending 88 GMC build thread
I need pictures!!!- BadBowtie 98
- Post #398
- Forum: Member Trucks
-
BadBowtie 98 Build Thread
- BadBowtie 98
- Post #581
- Forum: Member Trucks
-
BadBowtie 98 Build Thread
- BadBowtie 98
- Post #580
- Forum: Member Trucks
-
-
BadBowtie 98 Build Thread
Yea, it doesn't have shocks yet, but it rides pretty damn good without a swaybar- BadBowtie 98
- Post #576
- Forum: Member Trucks
-
-
-
-
-
BadBowtie 98 Build Thread
yea let me drive out the seal, then i can get you a better picture- BadBowtie 98
- Post #569
- Forum: Member Trucks
-
BadBowtie 98 Build Thread
Do you guys think its still usable? since there's still an edge, or should i be looking for a new Dana 44?- BadBowtie 98
- Post #567
- Forum: Member Trucks
-
BadBowtie 98 Build Thread
So the towel trick worked! i found this though... pretty sure its the housing, not the seal Not sure what to do with it- BadBowtie 98
- Post #566
- Forum: Member Trucks
-
BadBowtie 98 Build Thread
Thanks guys, heading out to start working on it :waytogo:- BadBowtie 98
- Post #565
- Forum: Member Trucks
-
6" RCX Lift owners chime in.
i think his is flipped over, if its not you need to do that- BadBowtie 98
- Post #3
- Forum: Stock Suspension + Bolt On Kits
-
BadBowtie 98 Build Thread
If i take the carrier out, of course gotta mark the caps but if the gears and carrier bearings looks good, can it go right back in? or do you have to shim it all over again? Or can i use new shims that are the same size and just replace those?- BadBowtie 98
- Post #562
- Forum: Member Trucks
-
BadBowtie 98 Build Thread
i already took them out, to replace them BFH and heat it is!- BadBowtie 98
- Post #561
- Forum: Member Trucks
