Search results

  1. WhiskeyTango93

    answer to any 4l60e trouble

    I thought I had # 28 going on.. Sooo , it wasnt that? i changed the fluid and filter , no difference.....4 days later , i move the truck into the shop and its not under load anymore in park and shifts into all gears f/r no prob..... Drives and shifts better than it ever has. WTF? Oh...
  2. WhiskeyTango93

    answer to any 4l60e trouble

    #28 happened to me yesterday.......I ONLY got 205K out of the thing.......oh well. I guess the mighty 4.3 was too much.
  3. WhiskeyTango93

    Post your lifted 2wd's!

    93 sclb W/T 4.5 ebay spindle , 1" block 17" pro Comp Steelies, 255/70-17 Goodyears. Yes i had stuff in the bed.... cali lean cause she's loaded
  4. WhiskeyTango93

    Stuff I'm working on

    Buy new center pins and start playin around :D
  5. WhiskeyTango93

    8 lug to 6 lug swap ?????

    Payload is the only suffrage here , as you're going from a full float to a semi float, thus putting the weight on the axleshaft , not the hub.... My.02.... Carry on , just watch the tongue weight/ trailer balance and you'll be fine
  6. WhiskeyTango93

    Stuff I'm working on

    on the 3+1 the 3rd has the guide wraps, so its gotta stay
  7. WhiskeyTango93

    Stuff I'm working on

    I've seen others take the 2nd leaf down out, but results may vary (*) lol.... :D
  8. WhiskeyTango93

    Stuff I'm working on

    Right at 1.5" , but the best thing was the gap from the top of the tire is exactly the same Front and rear. I'm picky about that kinda stuff:D
  9. WhiskeyTango93

    My low mile 1995 RCSB 5 speed.

    Welcome in!
  10. WhiskeyTango93

    Stuff I'm working on

    Before and after overload spring removal
  11. WhiskeyTango93

    Stuff I'm working on

    Wheels and tires are on , tune up done... The 88 has air injection and the wires were routed carelessly. # of them were fried due to contact with the air rails. TAKE YOUR TIME routing the plug wires on these trucks. At any rate , too much rake for me, gonna shitcan the overloads and see where...
  12. WhiskeyTango93

    Stuff I'm working on

    So apparently while i was converting the A/C to 134a , the water pump **** the bed......That's done now , all i have left is a basic tune up, the new exhaust and the uca camber bolt kit
  13. WhiskeyTango93

    Stuff I'm working on

    Here you go guys, I'm sending this one home tomorrow after I get the wheels and tires on...1988 scsb 5.7, 2/4 belltech spindle/hanger drop.
  14. WhiskeyTango93

    New Guy From Ohio

    What housings did you go with?
  15. WhiskeyTango93

    Stuff I'm working on

    94 v6 sr5 4x....gawd I wanted this in high school
  16. WhiskeyTango93

    Nor-Cal Roundup, anyone?

    Bump for info correction , Saturday the 27th. PM me for details
  17. WhiskeyTango93

    Sacramento Valley, CA roll call...

    Just curious who's active on here. Forums used to be the bomb......now its all FB n' crap.
  18. WhiskeyTango93

    Stuff I'm working on

    It's a 6 lug 4wd with a 14b sf rear. shoulda called it a k2000.......
  19. WhiskeyTango93

    Nor-Cal Roundup, anyone?

    2nd post in this thread has the details
  20. WhiskeyTango93

    Nor-Cal Roundup, anyone?

    West Sac , and our newly elected Mayor approves of people being responsible.
  21. WhiskeyTango93

    Nor-Cal Roundup, anyone?

    It's official , bump for details
  22. WhiskeyTango93

    New Dash Now Available 88-94

    How much did that set ya back?
  23. WhiskeyTango93

    90 4.3 rough idle, runs rough.

    Ive never had a tps affect idle on a TBI, unless its stuck open a bit ( speculation) I'd suspect a stuck injector or bad FPR. Double check the firing order? Oh yea, check the IAC
  24. WhiskeyTango93

    Stuff I'm working on

    How bout a 77 Olds Custom Cruiser Wagon! (no bs , the boss found it at a charity auction) 77K, and it's a 4bbl 403 car.
Top