Search results

  1. E

    steering wheel alignment

    i got the cunningham steering shaft. with front wheel straight ahead, pitman arm parallel to steering box, and stub shaft flat pointing up, when the flat on the shaft joint is aligned with the flat on the stub shaft the steering wheel is about 45 degrees turned to the left. the steering wheel...
  2. E

    keyless entry module 1995 suburban

    is this the keyless entry module? it's to the left of the steering column.
  3. E

    VSS harness on 241 t-case, 95 suburban

    hello the harness for the VSS sensor has ripped so I bought a replacement plug. does it matter which wire goes where on the sensor?
  4. E

    part missing on front bumper bracket

    what is it good for on the front bumper bracket and is it crucial?
  5. E

    adding trans cooler

    I bought for my 95 suburban the 96-99 GM trans cooler but the lines don't fit it. (the 95 cooler is discontinued). Is it possible to replace the quick connection fittings of the cooler with the old style ones to match the lines?
  6. E

    nss

    1
  7. E

    fuel pump and oil pressure circuits

    I'm trying to figure out how this circuit work. if both wires from C of the oil pressure switch and A3 of the relay are live and spliced- doesn't it make a short or sparks? and if there's no oil pressure, the pump is still getting power from the relay, so what makes the engine to stall?
  8. E

    4l80e vss and iss

    Doing an ls swap with psi harness on 95 k2500 suburban. The harness has iss and vss plugs. I understand that the iss is the front sensor, isn’t it? But there’s no rear sensor on the tranny. So where does the vss plug go?
  9. E

    LS swap with 4l80e- 1995 suburban

    I bought a PSI harness and pcm, and the instructions recommend getting a park or neutral signal to the pcm, by grounding a certain wire whenever the tranny is in these positions. where can I connect the wire to?
  10. E

    4l80e interchangeability between obs and nbs

    can a 4l80e from 2005 silverado with 261 transfer be mated to a 1995 suburban's 241 transfer? and can the 2005 torque convertor be installed in the 1995 tranny?
  11. E

    stall speed

    what's the stock stall speed for a 95 suburban 350 k2500 HD with 4L80E? I'm going to LQ4 swap it. Should I swap the torque converter too?
  12. E

    LQ4 swap to a 95 burb

    hello I bought an LQ4 from a 2004 Silverado which according to the VIN had 4L80E tranny, which is what I got now. does it mean it will bolt straight on without using aftermarket flexplate and spacer etc.?
  13. E

    5.7 vortec swap

    thinking of swaping my tbi suburban to a 5.7 vortec from a yukon donor. my truck has the 4l80e. if the donor has the 4l60e (don't know yet) does the vortec engine still fit my transmission? and do I need a different pcm and wiring for a 4l80e?
  14. E

    Problem with oil pressure gauge- 1995 350 suburban

    After cylinder heads job and new oil pressure sender the gauge started showing lower than before reading. After the first drive today it started dying and now “check gages” appears intermittently with the gage showing 0. Also check engine light appeared, it was 43 esc code. I disconnected the...
  15. E

    tbi downpipe to manifold springs

    i've been tightening the nuts on the springs with a torque wrench to 20nM and the springs just kept on compressing without getting to the torque until i stopped myself fearing to make a damage. they are brand new springs.
  16. E

    Tbi exhaust manifold problem

    What to do when the exhaust manifold probably shrank and can’t be installed? I’m afraid the spreading tool will crack it.
  17. E

    help with new lifters tbi 5.7

    I bought a set of new GM lifters. some of them slid down part of the way and stopped, I had to press on them and they rubbed the bore although I used the GM break in oil. After a week or so (without running the engine) I tried to get them out with a magnet so they come out maybe a 0.25 inch out...
  18. E

    loctite 592

    is it ok to use loctite 592 on coolant sensors threads, in the sense of ground conductivity?
  19. E

    Piston identification

    Hello Can you tell by this piston if it’s a below 8500 gvw or above 8500 gvw engine?
  20. E

    problem with gibson headers

    Bought those expensive headers and found that the through holes are too big for the bolts, which means you can wiggle the header around and never get the exact mounting spot. Any one had this problem with headers?
  21. E

    new flat tappet lifters

    do new lifters need to be primed/broken in before installation apart from coating with special oil?
  22. E

    wanted: 95 suburban 5.7 factory exhaust y-pipe

    3" outlet with O2 bung on the outlet. thanks
  23. E

    tbi manifold

    hello do these rectangulars have to be open? because there's no matching ports on the heads. and if not where does the exhaust gas enters the EGR from?
  24. E

    intake manifold removal

    what would you do if some coolant gets into the lifters after removing the intake manifold?
  25. E

    edelbrock performance heads

    hello does anybody have an experience with these heads for stock 350 TBI engine? https://www.edelbrock.com/performer-small-block-chevy-cylinder-head-hydraulic-flat-tappet-cam-60859.html

Latest posts

Members online

... and 15 more.
Total: 1,576 (members: 65, guests: 1,511)

Forum statistics

Threads
64,341
Messages
1,391,574
Members
51,448
Latest member
Tbuttion

Share this page

Top