Search results

  1. E

    steering wheel alignment

    I adjusted them to be the same length, without altering the toe.
  2. E

    steering wheel alignment

    the steering wheel can go on the shaft only one way around.
  3. E

    keyless entry module 1995 suburban

    and the factory manual says it's under the center of the dash...
  4. E

    steering wheel alignment

    i got the cunningham steering shaft. with front wheel straight ahead, pitman arm parallel to steering box, and stub shaft flat pointing up, when the flat on the shaft joint is aligned with the flat on the stub shaft the steering wheel is about 45 degrees turned to the left. the steering wheel...
  5. E

    keyless entry module 1995 suburban

    what does that modul look like? I didn't find anything to the right of the column, but I found this one hanging.
  6. E

    keyless entry module 1995 suburban

    that chopped wires looks pink but according to the manual it should be white and it's "ignition switch output, off, run, crank", going to or from trans fuse. any idea what it does?
  7. E

    keyless entry module 1995 suburban

    is this the keyless entry module? it's to the left of the steering column.
  8. E

    VSSB Drac wiring question

    I hope it doesn't matter.
  9. E

    VSSB Drac wiring question

    can you check which wire is connected to which pin in your VSS? I have to put there a new plug and don't know which way to wire it, if it matters at all.
  10. E

    VSS harness on 241 t-case, 95 suburban

    hello the harness for the VSS sensor has ripped so I bought a replacement plug. does it matter which wire goes where on the sensor?
  11. E

    part missing on front bumper bracket

    what is it good for on the front bumper bracket and is it crucial?
  12. E

    adding trans cooler

    the 88-95 cooler ends are different. the fitting is indeed 3/8 but I think it's NPT... does it fit an NPTF female? the 96-99 cooler 89022535 I bought from rockauto and it's still available today. they have also GM lines for both 88-95 and 96-99. the fittings are indeed discontinued but I found...
  13. E

    adding trans cooler

    I bought for my 95 suburban the 96-99 GM trans cooler but the lines don't fit it. (the 95 cooler is discontinued). Is it possible to replace the quick connection fittings of the cooler with the old style ones to match the lines?
  14. E

    nss

    1
  15. E

    fuel pump and oil pressure circuits

    so the oil pressure switch is not intended to protect the engine from loss of oil pressure as some people believe?
  16. E

    fuel pump and oil pressure circuits

    I'm trying to figure out how this circuit work. if both wires from C of the oil pressure switch and A3 of the relay are live and spliced- doesn't it make a short or sparks? and if there's no oil pressure, the pump is still getting power from the relay, so what makes the engine to stall?
  17. E

    L29 0411 Swap - Struggling with crank relearn and P0300

    correct. they ask to ground a single wire from the pcm when in P or N. I found a green wire on the c200 connector that gets voltage when in P, so I can use a relay to ground that pcm wire. I still remain with the N problem.
  18. E

    L29 0411 Swap - Struggling with crank relearn and P0300

    so if I test for voltage with a test bulb either wire somewhere after the cluster as in the picture it won't lit the bulb? should I test ground by checking for continuity between the wire and ground? I have a single wire with the psi harness that needs to be grounded when in N or P so I...
  19. E

    L29 0411 Swap - Struggling with crank relearn and P0300

    this is the 95 diagram. I totally don't understand it. what are the 4 ranges and and what's the parity shmarity? and how does it show 7 positions on the cluster? I was thinking that those 4 wires should light a grounded test bulb between the cluster and the tranny but no.
  20. E

    L29 0411 Swap - Struggling with crank relearn and P0300

    i want to do the same on my 95. I found a wire that has voltage when in park (the green wire on center bottom of c200), but can't find anything for neutral. the plug with 4 wires on the tranny doesn't have voltage although the position indicator in the instruments is working.
  21. E

    4l80e vss and iss

    so if the vss is on the transfer case, the plug that I got in the harness doesn't fit. the 2 sensors are different. is there an adaptor for it?
  22. E

    4l80e vss and iss

    Doing an ls swap with psi harness on 95 k2500 suburban. The harness has iss and vss plugs. I understand that the iss is the front sensor, isn’t it? But there’s no rear sensor on the tranny. So where does the vss plug go?
  23. E

    LS swap with 4l80e- 1995 suburban

    it has the round big connector, the VSS connector and the ISS connector which I don't know what it is.
  24. E

    LS swap with 4l80e- 1995 suburban

    I bought a PSI harness and pcm, and the instructions recommend getting a park or neutral signal to the pcm, by grounding a certain wire whenever the tranny is in these positions. where can I connect the wire to?
  25. E

    TCC unlock wire

    I've found this wire behinde the glove box on the c200 connector and on one of the pcm connectors. But they want another wire that does the opposite- gives 12V when the brakes are applied so the dbw throttle body can function. where do I find it? it's a 95 suburban and the factory electrical...

Latest posts

Members online

... and 32 more.
Total: 1,458 (members: 82, guests: 1,376)

Forum statistics

Threads
64,315
Messages
1,391,261
Members
51,413
Latest member
inconceivablemotors

Share this page

Top