Search results

  1. Kamd90Chevy

    A/C Bypass/Delete Pulley

    Yea I'm beginning to think that's gonna be my only option to try and remedy the issue.
  2. Kamd90Chevy

    A/C Bypass/Delete Pulley

  3. Kamd90Chevy

    Post your lifted 2wd's!

    Has anyone looked into the newer Rough Country 6" lift?
  4. Kamd90Chevy

    A/C Bypass/Delete Pulley

    I've changed my belt tensioner twice (warrantied), an idler pulley, replaced the P/S pump pulley with a NOS GM pulley, water pump and swapped the pulley with an OE style replacement, TCI dampener when the original one finally started to separate, recently warrantied the alternator when I...
  5. Kamd90Chevy

    A/C Bypass/Delete Pulley

    Ok I'm at my wits end. About 6 months ago I removed my compressor after the pulley seized. Ever since I have battled this incessant belt squeal. Originally was only at start up to warm/low idle, progressively worked it's way to anytime it runs. I'm 99.9% sure that it's not tracking true, the...
  6. Kamd90Chevy

    CEL for Code 24

    Hey guys, my 90 RCSB 5.7/700r4 intermittently throws the CEL and I finally got it to stay on long enough for me to check it and its code 24 Vehicle Speed Sensor (VSS) Short Circuit. Now Google lead me down a couple paths of things to check and so far all I can say is my dash works just fine and...
  7. Kamd90Chevy

    Lower Radiator Hose Problems

    Well your reply made me think, open my damn tool box and use my tools lol. I hooked up my Matco pressure tester and put 16 pounds on it. The lower hose at the pump, the heater hose at the radiator side, and the upper radiator hose at the t-stat housing all leaked. Had to remedy all of them. Then...
  8. Kamd90Chevy

    Post your lifted 2wd's!

    Ok so i'm ordering the RC 4" spindle lift and the notes state that Light duty brake trucks need to change brakes to make it function. I know i'm looking at Pads, Rotors, Bearings and Seals. Am I also looking at calipers and brackets? I already have Russell stainless braided lines and 3 months...
  9. Kamd90Chevy

    Lower Radiator Hose Problems

    OK guys, I've been wrenching since i was 9 with my Dad. I'm no master tech but this is really starting to gripe my bum. I've had a problem with my lower radiator hose leaking past the clamp at the water pump side for months. So i changed the lower hose and clamps, thinking the rubber was aging...
  10. Kamd90Chevy

    94 C1500 Suburban HVAC Control Issue

    Ok so i found out if u cross the 2nd pin from the left on the connector and use a test light to close the connection on my 90, it kicks the blower. So after everything else i tried it on the 94 Burb and it would only kick the relay (which i ended up following the wires to a bracket with 4 relays...
  11. Kamd90Chevy

    94 C1500 Suburban HVAC Control Issue

    Well i had the 2 junkyard units with me at the house and i tore my 90 apart and hooked them up knowing mine worked, and neither used part functioned. So that ruled that out. And unfortunately that is my luck these days. Trying to avoid the $100 on the new one from LMC Truck. But i haven't made...
  12. Kamd90Chevy

    94 C1500 Suburban HVAC Control Issue

    So out of curiosity I went to the junkyard and bought 2 other HVAC controls for about 15 bucks. i tried installing both of them and got the same results. So I guess i'll be ordering a new one. I want to take mine off my truck that i know works and plug it into his but i'm super sketch about if...
  13. Kamd90Chevy

    94 C1500 Suburban HVAC Control Issue

    Hey guys and gals, i bought my dad a 94 Burb a couple months ago and have been working on it off and on as my work schedule allowed. I got all the mechanical taken care of, some tires and brakes, new light kit etc etc. However, the one thing ive not been able to get to work is the damn HVAC...
  14. Kamd90Chevy

    1990 C1500 ABS (RWAL) removal.

    Finally got around to doing this to my 90 RCSB 2wd. Even after i had swapped on the SSBC brake kit and changed the calipers, i still was getting the notorious bounce. After this delete, my pedal is always solid and no brake fade or bounce. I also added a set of Russell stainless line kit for the...
  15. Kamd90Chevy

    Project; Burnt Up

    Just out of curiosity, did you ever happen to look at what size tire they had on the 15's on the rear? I'm oddly curious how they stuffed that in stock tubs.
  16. Kamd90Chevy

    98 Yukon Timing Set

    Michael, I wasn't trying to question your knowledge of the replacement parts. But, I work 6 days 12 hours a day and will be tackling this on my next availale Sunday and will be ordering all the parts ahead of time and hopefully wont have much else wrong that wouldn't be available at a local...
  17. Kamd90Chevy

    1990 C1500 ABS (RWAL) removal.

    sounds like a plan, shes sitting till this weekend when im off Saturday. Gonna go through it all again, plus i need to do the oil change, get the HID's out and back to the regular headlights. and an oil change on the womans daily. ill hop back on if it doesnt work, thanks for the help everyone.
  18. Kamd90Chevy

    1990 C1500 ABS (RWAL) removal.

    ok so i took the pressure switch connector off and fired her up and went for a drive, the light stayed off. i came back, plugged it back in and did the same trip, driving the same way, and the light came on the first time i hit the brakes and stayed on. Is this a sign i need to re-bleed the...
  19. Kamd90Chevy

    1990 C1500 ABS (RWAL) removal.

    ok so i did the mod and as all the posts have said, huge huge difference in the pedal and performance. however, the 1st trip out everything was fine, the 2nd trip my brake light came on and has stayed on since. i went over all the fluids, lines, hose connections and wheel cylinders. everything...
  20. Kamd90Chevy

    98 Yukon Timing Set

    ok but what is that decision based on? is it actual replacement or is that just the "norm" replacement option
  21. Kamd90Chevy

    98 Yukon Timing Set

    hey guys i'm tearing into my dads 98 Yukon 5.7 to do the timing chain set and some other maintenance while i'm in it, but when i went to order the parts before getting it tore down, i'm running into different width sets. These are the options posted, .275", .280", .285" or .405" sprockets. is...
  22. Kamd90Chevy

    Floating Rotor Swap on 90 RCSB LD Brakes

    Yea i understand now why thats a no go. damn if something that seems so close makes it so far from working. i gave in and ordered the SSBC Rotor and Pad upgrade kit and ACDelco bearings and wheel seals. Also grabbed my inner and outer tie rods and sleeves while i was at it. almost have it all...
  23. Kamd90Chevy

    Floating Rotor Swap on 90 RCSB LD Brakes

    So no one has ever tried using 4 wheel drive spindles off like the 92+ trucks with the floating rotor style? I've almost got all my Moog front end replacement parts to rebuild the steering piled up. And I don't see sinking the 203 on the SSBC slotted kit from Summit when I'm going to get, what...
  24. Kamd90Chevy

    Floating Rotor Swap on 90 RCSB LD Brakes

    ok so my fellow Gmt400 Gurus. i have been proposing an idea of using the spindle/bearing/brake set up off a 4 wheel drive of our body style. a fellow GMT400 fan of mine has multiple C and K series 2500 Suburbans, after much lifting and removing of tires on multiple trucks of his and doing...
  25. Kamd90Chevy

    Lowered Chart with Images

    Whipped i think i need 3/5 to get the stance i want. Gonna be using Centerline Competition Qualifiers 15x10 with 3.50 bs and running the Nitto 555r's to help it out a bit with staying planted. i have a terrible time keeping it on the ground.

Latest posts

Members online

... and 15 more.
Total: 1,371 (members: 65, guests: 1,306)

Forum statistics

Threads
64,322
Messages
1,391,325
Members
51,420
Latest member
vancecamp

Share this page

Top