Search results

  1. Arkansasdave

    brake issues

    Sorry guys I thought we all were here to help each other sorry to have bothered you guys i will not waste anymore of your time. I have been a member of many forums for over 20 years and never been greeted like this. Dave
  2. Arkansasdave

    brake issues

    I used a vacuum bleeder on the calipers and one would not produce any fluid. So I got some assistance and pumped them up to bleed and finally got fluid but it is still locking when the pedal is pressed. I opened the bleeders and relieved the pressure on front and then was able to back it into...
  3. Arkansasdave

    brake issues

    So I got my clutch issue fixed and now the front wheels are locking up it did this a little awhile back but went away and now it will not move just spins rear wheels I jacked it up and the rears turn I just did a brake job on them a month or so ago but and bled out everything and now the fronts...
  4. Arkansasdave

    Clutch issue

    yes but it was the clutch master cylinder and they said they couldn't find it on their computer. So I forgot where there store was located and went to another parts store and bought a new one with warranty where I have had good luck before with warranty issues. Now I'm fighting the brakes. Dave
  5. Arkansasdave

    Clutch issue

    Got the clutch all bled out and it works like new now. I ran into an issue when trying to drive that I add a few weeks back it has a brake locking up I have replaced the rear brake shoes a few weeks ago and took them back apart yesterday to back off the shoes but that didn't fix it I think it...
  6. Arkansasdave

    Clutch issue

    so I did a little diagnosing and research and determined that my clutch master cylinder might be bypassing the seal and not putting all the fluid to the slave. So I removed the old one with 27000 miles and sure enough it was leaking from the rear where the rod goes in and I replaced it with a...
  7. Arkansasdave

    The Member Truck Thread

    a couple more photos I still have to get a new air dam and am currently getting it ready to daily drive for awhile so it don't just sit in the garage. Dave
  8. Arkansasdave

    Clutch issue

    Thinger2, Sorry for the slow reply been tied up all week at work and didn't get a chance to get on the forum. The fluid does look dirty I was planning to flush and change it so that is the first thing i'm going to try. I have a clutch bleeding tool that is a pressurized tank to push clean...
  9. Arkansasdave

    Clutch issue

    The clutch, throw out bearing, pressure plate, pilot bearing, slave cylinder,clutch master cylinder and line to slave cylinder have 27000 miles on them I had put 10,000 in parts in the truck a few years back when I went through it and refreshed everything since new. Dave
  10. Arkansasdave

    Clutch issue

    Ok thanks there was no noise just normal sounds Dave
  11. Arkansasdave

    Clutch issue

    I started my 90' today and when I pushed in the clutch it had pedal at first then just went limp to the floor but let the 5 speed go in 1st gear but didn't release so I turned the truck off tried to pump up the pedal after checking fluid in the reservoir and it was full. It did not pump up so I...
  12. Arkansasdave

    Post your other projects

    Here are a couple of my other projects and I have another I will post after I get some pics. The first is my 2005 silverado L33 H.O. 5.3 extended cab 4x4, the second is my 79 international Scout II with a new 4 bolt main 355 with a extreme 4x4 comp cams cam, Eagle rods, speed pro hyper eutectic...
  13. Arkansasdave

    The Member Truck Thread

    thanks!
  14. Arkansasdave

    The Member Truck Thread

    Hello everybody here I just signed up here is a pic of my truck I've had it stored in the garage for awhile and got it out and am getting it all cleaned up and ready to drive again. It has a vortec 355 with a comp cams 480-280 magnum cam, holley street avenger intake, accel distributor and coil...
Top