Search results

  1. S

    Used vortec 454 fuel rail. $15 plus shipping obo

    Is the rail still available?
  2. S

    Vortec 7.4 rough idle

    Update: I used the dashcommand app with a cheapy tablet and set the cam retard. It took awhile to figure out all the technical stuff. (Dealer wanted $200 to set it.) I was close at 8.3 degrees. Got it set to 0.0 at 1150 rpms and finally buttoned everything up. The truck runs like a dream! So...
  3. S

    Vortec 7.4 rough idle

    Some good news... after changing the plugs, wires and FPR it’s idling good now. I took advantage of the plenum being off to restab the distributor without all the tweaks and turns you have to go through to get it in when the plenum is in the way on the 454. Crazy thing is that it took awhile to...
  4. S

    Vortec 7.4 rough idle

    I’m going to replace the fpr. I compared the gear with the old one they are exactly the same. Dipple side is between two teeth and the pin hole on the non dimple side is on a tooth.
  5. S

    Vortec 7.4 rough idle

    Possibly, how’d you get it in spec then?
  6. S

    Vortec 7.4 rough idle

    And what about my FPR? Truck has always been hard starting. I replaced injectors, filter, FPR and pump recently trying to solve this issue. Fuel pressure drops immediately after key is turned off. When I clamped return line the pressure stayed without any drop off so it must be losing pressure...
  7. S

    Vortec 7.4 rough idle

    It idled okay before the distributor gear broke so I’m still thinking the distributor is still off. But I’ve reinstalled it probably 20 times and it only wants run in one position. One tooth either way and it doesn’t run or barely runs. I doubt I’m 180 degrees out as it wouldn’t run at all. Is...
  8. S

    Vortec 7.4 rough idle

    Plugs look like sh$t. Plus most were finger tight. If not the problem I’m having it would certainly become a future problem.
  9. S

    Vortec 7.4 rough idle

    Checked compression, all cylinders 150 lbs. But spark plugs badly fouled. Gas residue on threads and about 6 plugs were only finger tight. (The previous owner changed the plugs, bright individual.) anyways, looks like I’m gonna need new plugs and wires. I’m guessing the timing is still off...
  10. S

    Vortec 7.4 rough idle

    The regulator responded to the vacuum line being disconnected so I’m gonna say it’s good. When I clamped off return line pressure stayed when I shut the key off so it has to be leaking down the return line. Either way I doubt that’s my misfire problem. I tried stabbing the distributor again...
  11. S

    Vortec 7.4 rough idle

    From what I gather the spring inside the regulator is controlled by vacuum. At idle you have vacuum which opens the flow to return line. Under load there’s no vacuum, return is closed and pressure should be slightly higher. After cycling the key without starting, I get 62ish psi then it drops...
  12. S

    Vortec 7.4 rough idle

    I followed the service manual procedure. Said to shut off return line and recheck pressure. If above specified amount (55-65 psi) regulator is bad. I got over 90 psi. I’ve replaced the regulator awhile back so I’m skeptical it’s bad.
  13. S

    Vortec 7.4 rough idle

    I did a fuel pressure check at the rail. Clamped off return line and it read above 90 psi with key on. Bad regulator?
  14. S

    Vortec 7.4 rough idle

    Seems to be where it's idling then. I'll try to re-stab it one more time. It really has me scratching my head. I hope it didn't jump time or something chaotic like that. It only has 80k on it so hard to believe if that was the case.
  15. S

    Vortec 7.4 rough idle

    No luck on better idle. I’m thinking I must still be off a tooth. Given that the crank and cam sensor has been disrupted, that maybe why I’m not getting the p1345 code. Also, when I point a timing light at the damper it’s firing several degrees before the mark. I know timing lights are not...
  16. S

    Vortec 7.4 rough idle

    I found the thread on this forum. https://www.gmt400.com/threads/case-learn-or-crank-relearn.6423/ I’ll give it a shot. I definitely need a scanner to set the cam retard. I’m gonna try using car gauge pro or the dashcommand app. Just trying to save a trip to the stealer!
  17. S

    Vortec 7.4 rough idle

    Update: I swapped distributor gears and put the old distributor back in as well as changed the EGR valve. It’s maybe a little better but basically the same rough idle. I’m thinking I need to get the new crank sensor relearned. I’ve read places that 98 and older is set with a driving procedure...
  18. S

    Vortec 7.4 rough idle

    Update: tested the egr valve per this website https://easyautodiagnostics.com/gm/4.3L-5.0L-5.7L/egr-valve-tests-2 and it showed below the 0.6-0.9 ohm range it’s supposed to be at, it was around 0.4-0.5 ohm. Every other test on it checked out fine. Truck has always has a little tapping noise...
  19. S

    Vortec 7.4 rough idle

    Tried it and no difference plugged in or not plugged in.
  20. S

    Vortec 7.4 rough idle

    I’ll try it. What should I be looking for? Better idle or worst? Thanks
  21. S

    Vortec 7.4 rough idle

    I agree it needs to be set with a scanner to get perfect spec. Just seems odd it would idle rough and not throw the cam code if it was causing the issue.
  22. S

    Vortec 7.4 rough idle

    I’ve had the old distributor out before when I changed the fuel rail a few years ago. Installed it wrong and it gave me the code for cam correlation upon initial start up.
  23. S

    Vortec 7.4 rough idle

    Set the distributor with proper procedure. TDC on #1, fired right up no cmp code so must be within 2 degrees of spec.
  24. S

    Vortec 7.4 rough idle

    Spectra oem distributor. I could try putting a new gear on the old one and see if there’s a difference but I doubt it. Would a code be thrown if the crank sensor needed to be relearned?
  25. S

    Vortec 7.4 rough idle

    Hey guys, hoping to pick your brains on a rough idle issue I’m having with my 97 GMC 2500 pickup, 454, 80k miles. Long story short, I had a blow out towing my 30ft travel trailer a few weeks ago. Engine died pulling a hill, no restart. Upon diagnosing, I found the pin gear on the dizzy stripped...
Top