Search results

  1. T

    Aftermarket double din radio is the stock 1988-93 digital stereo location?

    I am looking into a RPI and an lcd in the cubby hole area but I suck at 3d design lol...
  2. T

    Lowering a 4x4

    Lowered and swap in the AWD trans like they did on... PowerNation? Rally truck at that point.
  3. T

    Toy trucks for sale

    ext cab black k1500 of some sort would be cool? Trucks only for me
  4. T

    Toy trucks for sale

    I am not sure if this is still a thing but if so... what is left?
  5. T

    3D Printed a Dome Light Lens

    Nice! I want to start designing some things to make on my printers.
  6. T

    Air / Heater / Temperature actuators

    Ill look closer but my labels are so so soooo faded, that was half of my battle :(
  7. T

    Air / Heater / Temperature actuators

    Ah yeah I totally spaced on the year haha... It is a 99 K1500 Ext Cab I looked closer and they are all 6 pin I just found this: You don't mention year or model of truck. For the 1998 K1500 the one in the drivers side footwell is the mode door which directs air to which vents depending on the...
  8. T

    Air / Heater / Temperature actuators

    I pulled my HVAC and cleaned it but didn't take pictures or make notes of where which actuator goes where. I have 3 actuators. 2 are 5 pin, one is 3 pin. I just don't want to put it back together and have to pull the dash again :(
  9. T

    Bulb Sockets Find

    https://www.rockauto.com/en/catalog/chevrolet,1998,k1500+pickup,5.7l+v8,1303614,electrical-bulb+&+socket That is a massive section called Electrical Bulb & Socket lol
  10. T

    Bulb Sockets Find

    RockAuto for sure. I was just looking at them for mine.
  11. T

    Pcm compatibility

    At that point, I would do the 0411 swap. Its easy, takes a few hours. And then you can really tune it.
  12. T

    Aftermarket keyless tied into factory keyless

    Yeah I needed to use 3 wire, so no cutting of the factory stuff, just tap into the line. https://www.the12volt.com/relays/relaydiagram1.html
  13. T

    Aftermarket keyless tied into factory keyless

    1999 K1500 I have kind of a strange setup. My truck shows the RPO code for factory, has the remote yet, all that fun stuff. I am wiring in a Compustar CM700 something or other. There was already a remote start in there that was mostly pulled out. At this point I have ran all new cables and made...
  14. T

    0411 initial tune

    PCM Hammer is not letting me erase the flash memory 2:206] Initializing CRC algorithm on PCM, this will take a minute... [10:04:53:066] Requesting CRCs from PCM. [10:04:53:083] Range File CRC PCM CRC Verdict Purpose [10:04:58:011] 060000-07FFFF A1E37653 A1E37653...
  15. T

    0411 initial tune

    I am so so so so so sorry! I meant l31 5.7. I dont know how I typed LS. Ugh. Didnt mean to cause any rifts haha. SO YEAH. L31 with 4l60e and NP243C (99% sure) with 0411 going in. Base tune to get it going and keep 4x4 somehow? Swapping of segments? Start with Van tune and swap in system info...
  16. T

    0411 initial tune

    Start with a van tune? Should be just fine? Swap in a S10 segment about 4wd? I am nervous. I got my bench harness in today and have quite a few different bins I have been trying to make correct. I havent started the pinout swap yet. I did contact lextech about getting a pinout and base tune, but...
  17. T

    0411 initial tune

    I have a 99 K1500 5.7L Vortec. I am sure its called an L31. BUT. I bought an 0411, have an OBDlink SX (slow, I know), and a bench harness. I want to figure out my first flash. From what I read, I would be best getting a S10 BIN file with a 4l60E and 4wd and segment swap in the 5.7l part and...
  18. T

    The Stupid Lift Questions Thread

    My apologies for the late reply! I have 99 K1500. I will have to go take a peak under someone's truck soon. Steering is cocked off to the side a little bit as well, so its ready for a lot of things. I would I think think everything replaceable should be, if its going to be apart. I have people...
  19. T

    The Stupid Lift Questions Thread

    I have a 4 inch Superlift on my truck. I know so little about it... But. The front end needs rebuiling. Do I need any special arms or brackets or anything for the rebuild? I was looking into like... Upper and lower A arms I think they are called... and bushings, and ball joints and whatnot...

Latest posts

Members online

Total: 1,244 (members: 41, guests: 1,203)

Forum statistics

Threads
64,335
Messages
1,391,504
Members
51,440
Latest member
lolxnico

Share this page

Top