Search results

  1. M

    1997 K3500 - NV4500 Clutch Hose Fitting Removal

    This is a rookie question, but how am I supposed to disconnect these fittings from the master and slave cylinder? My clutch hose has a leak and needs to be replaced.
  2. M

    Turn signal wiring harness?

    I’ve always had power to the taillights but I’ve always had issues with the turn signals not flashing like they should. Basically they would flash but not very brightly
  3. M

    Turn signal wiring harness?

    My truck has had nothing but issue after issue with the turn signals and taillights. I put a new bed on, and now I don't have any power running through the harness that runs down the driver side frame channel. At this point I'm ready to put in a whole new harness for all the lights. Does anyone...
  4. M

    Turn Signals Not Working

    Standard. I should update the post and mentioned that I just messed around with it some more and it appears that none of the signal stalk functions are working (wipers, etc)
  5. M

    Turn Signals Not Working

    The turn signals in my 1997 Chevy K3500 (6.5 diesel) aren't working. I noticed that the left hand signal indicator stayed lit on the dash, and that one of the parking light bulbs was out, so I replaced all of them. Now when I start the truck, both turn signal indicator lights stay on the dash...
  6. M

    No crank, no start on new crate engine

    Hey all, I finished installing my crate engine in my 1990 K1500. It is a 350 and I am still running the original TBI setup. I have everything in place and ready for cam break in, but when I turn the key nothing happens. My headlights work, I get power to the dash, and I can hear my fuel pump...
  7. M

    Help adjusting throttle cable

    Hey all, I have a 1990 K1500, and I have installed a new crate engine (haven't fired it up yet though). It has a 350 TBI, and I'm running an Edelbrock intake manifold- so the throttle body sits up a little higher, and pulls on the throttle cable a little. Now there is very little room for my...
  8. M

    I managed to kink this line while doing an engine swap and need help

    Hey all, I managed to kink this line really badly while doing an engine swap (even worse than the picture). I'm new to all this and don't have a part number for it, much less know what it's called. Can anyone help me please?
  9. M

    Anyone know where I can get a replacement for this connector that goes to my alternator?

    I've been working on undoing electrical connections in preparation of removing my engine, and managed to sheer this connection right off the wire that runs to my alternator. I drive a 1990 Chevy K1500 with a TBI 350. I figured I could get a standard electrical connector that's the same size...
  10. M

    Young guy replacing an engine for the first time; any advice or recommendations?

    Well, unfortunately my old 350 TBI motor bit the dust today. It started knocking really badly while driving today and I don't want to risk it dying on me considering I drive pretty long distances regularly. I want to replace it with another 350 TBI engine; nothing too crazy, and I'm ok with...
  11. M

    Question about crankcase ventilation hose vs. breather

    This is going to sound like an incredibly silly question, but how did you go about extending those hoses? I'm guessing I will have to buy generic hose rated for use in the PCV system and cut it to fit?
  12. M

    Question about crankcase ventilation hose vs. breather

    Hey all, I am working on cleaning up the engine bay on my truck (1990 K1500 with a 350), and bought ProForm valve covers. These valve covers look great and fit well, but the crankcase ventilation and oil fill locations are opposite of the factory covers. I was wondering if I could replace the...
  13. M

    What are Your Favorite Valve Covers?

    Thank you! I will have to measure the gap between my valve cover and AC hoses to make sure they will fit. I really appreciate it!
  14. M

    What are Your Favorite Valve Covers?

    Did you have to run different PCV and breather grommets than factory size to make those work?
  15. M

    What are Your Favorite Valve Covers?

    I have a pretty nasty valve cover leak on the passenger side and am going to take this opportunity to replace the factory valve covers with something much nicer looking. I've been looking online though and there are a lot of complaints that certain ones won't fit people's trucks. I have a 1990...

Latest posts

Staff online

Members online

... and 18 more.
Total: 1,721 (members: 68, guests: 1,653)

Forum statistics

Threads
64,249
Messages
1,389,859
Members
51,240
Latest member
Baelfor

Share this page

Top