Search results

  1. Canon Lansdell

    Near-factory AUX switch

    ISO of a factory style auxiliary switch for a light bar. Something that would go above the cargo light switch and not look out of place. Did any GMT400’s come with such switch? I’ve been fog light switches but am looking for one that would say aux light (or something of that nature).
  2. Canon Lansdell

    No Spark

    I just replaced my head gaskets on my 98 5.7,and once i got everything back together and the distributor set, i tried to start it and wasn’t getting any spark to the wires. ignition coil is firing and cap and rotor were fine before i took everything apart. Is it possible they would’ve just went bad?
  3. Canon Lansdell

    Cracked Cylinder Head

    I have a cracked head on my 98 K1500. I’m pretty sure it’s on a coolant jacket on the 8th cylinder. Is it worth getting it welded up or should I buy a junkyard head?
  4. Canon Lansdell

    Misfire! Help!

    Hello all. I have a severe misfire on my 98 K1500 that started randomly while driving weeks ago. Misfired on almost every cylinder intermittently, but most on cylinder 6. First thing i changed was spider unit to MPFI setup. Read 55 psi (should read 60-65) fuel pressure. Next changed fuel filter...
  5. Canon Lansdell

    Door lock problem

    I have a problem with the power locks on my 98 silverado. on occasion, the fob will honk the horn but not lock the door, and then when you lock it from the inside, it will blow the fuse. it does it once or twice a month and only blows the fuse when using the drivers side button. i recently got...
  6. Canon Lansdell

    List of Problems

    I have a 98 K1500 (5.7, 4l60e, electronic shift transfer case) and i have a couple of problems and would appreciate any and all input on some fixes. Engine was rebuilt when i bought the truck. Previous owner threw a rod. 1. Engine doesn’t always rev when started as a fuel injected engine should...
  7. Canon Lansdell

    Suspension Rebuild

    Looking to buy a rebuild kit for my front suspension on my 98 z71. Any recommendations? Found a kit on 1A Auto for ~$105.
  8. Canon Lansdell

    Need body work suggestions

    Got a few spots on my body i’d like to correct. Not too much money on hand so i’d preferably do it myself. Any suggestions?
  9. Canon Lansdell

    Does fleetside bed come apart?

    I have a 98 Silverado with a fleetside bed that is damaged beyond my extent or repair. Bulging, dents, and dings. The whole 9 yards. I was wondering if you could take the single panel off of the entire bed without cutting the metal. I've seen LMC sells the body panel, even though if it's...
  10. Canon Lansdell

    Gas Gauge Wrong

    Since I got my 98 k1500, the gas gauge has read way past full and hits E when it still has a few gallons left. It’s a new fuel pump w/ sending unit so that shouldn’t be the problem. Also, it’s shown the same on multiple clusters. Wondering if there is any fix?
  11. Canon Lansdell

    High Oil Pressure

    Hey I need some help. So I bought my 98 Silverado (5.7 350 EFI) at 146k miles with a rod knock. Fast forward, the engine is rebuilt and back in the truck. Oil pressure runs at 70+ psi almost constantly. Oil pump was reused in the rebuild. Also, Cam to Crank correlation sensor is throwing a CEL...
  12. Canon Lansdell

    High Oil Pressure

    Hey I need some help. So I bought my 98 Silverado (5.7 350 EFI) at 146k miles with a rod knock. Fast forward, the engine is rebuilt and back in the truck. Oil pressure runs at 70+ psi almost constantly. Oil pump was reused in the rebuild. Also, Cam to Crank correlation sensor is throwing a CEL...

Latest posts

Members online

Total: 1,157 (members: 24, guests: 1,133)

Forum statistics

Threads
64,254
Messages
1,389,894
Members
51,247
Latest member
Quasar

Share this page

Top