Search results

  1. Soflanick911

    The Stupid Lowered Questions Thread

    Did the swap, now how In the hell do you tighten the rear bolts on the uca’s? Is there a trick?
  2. Soflanick911

    A/C accumulator question

    in the same boat. Line is twisted, not closed off though just slightly crimped. Would cutting off the dryer save me from having to remove the evaporator? really not happy with this situation. bringing back a thread from the dead
  3. Soflanick911

    5/7 drop question ???

    Any clearance issues with the 2” control arms and 3” springs? About to rip out my 2” springs for the 3” ...
  4. Soflanick911

    Swap Meet Slam

    my man.... thank you sir!!!!
  5. Soflanick911

    Swap Meet Slam

    hey bud, could you give me a measurement of the front wheel opening from the ground to the fender? in line with the hub. ride height looks perfect.
  6. Soflanick911

    The Stupid Interior Questions Thread

    gotcha, well i ordered the navy blue... looks to be the same lol guess well see
  7. Soflanick911

    The Stupid Lowered Questions Thread

    a truck i just acquired has a DJM lowering control arm (2") and a 2" lowering spring. Which comes in their 4/6 kit. would a 3 inch lowering spring work to replace the 2" for a 5" drop? or would it open up a can of worms?
  8. Soflanick911

    The Stupid Interior Questions Thread

    hey guys i have a 1995 c1500 with the blue interior. 26D is the RPO code. Im trying to get new carpet. Do you happen to know if the acc navy blue is one in the same?
  9. Soflanick911

    Rare paint codes

    mystic teal i think
  10. Soflanick911

    4/6" Notched

    honestly OP your truck kinda looks like it already has a 4/6 drop
  11. Soflanick911

    "1500" on replacement door molding

    any updates on this? just ordered new molding from LMC, what is my best bet for the 1500 badge.... stick on the molding?
  12. Soflanick911

    "1500" on replacement door molding

    yep i screwed up tossing the emblems.... good luck
  13. Soflanick911

    The Stupid Lowered Questions Thread

    that measurement was from the hub to the fender. ill check the height on the springs tomorrow when i go to finish the swap but im pretty sure they were around the same height. I emailed djm, they said i seem to have the right springs, grey hammered, and right part no. its possible it didn't...
  14. Soflanick911

    The Stupid Lowered Questions Thread

    question.... i removed the mcg 2" drop spring and replaced it with a 3" djm spring. the 3" spring dropped it a total of a quarter of an inch compared to the mcg. how long until it fully settles do you guys think? or is there something wrong.....
  15. Soflanick911

    Rear disc.......again Little Shop manufaturing kit questions

    Ah then yeah this kit makes complete sense. I only went disc because my drums were worn... perfect time to upgrade. Good luck.
  16. Soflanick911

    Rear disc.......again Little Shop manufaturing kit questions

    it went pretty well, I think it’s worth it, the brake line was kind of a pain to connect but for the most part it was pretty straight forward. I used a sawzall to remove the drum plates. the upgraded master is nice too, Much better pedal feel and braking power.
  17. Soflanick911

    Rear disc.......again Little Shop manufaturing kit questions

    it went pretty well, I think it’s worth it, the brake line was kind of a pain to connect but for the most part it was pretty straight forward. I used a sawzall to remove the drum plates. the upgraded master is nice too, Much better pedal feel and braking power.
  18. Soflanick911

    JWall's 98 Reg Cab SWB

    Following you on IG, clean build man. I had a Red 95 with the maroon int in HS... always will be the one that got away LOL.
  19. Soflanick911

    Cost For Alignment

    I paid 100 for a recent alignment with tip. The shop specializes in front end work. Those shops are getting hard to come by these days...
  20. Soflanick911

    Rear disc.......again Little Shop manufaturing kit questions

    i am planing to install the LSM rear disc and master cylinder upgrade tomorrow, Anything in particular that i should know? Essentially bench bleed master, swap to disc, bleed system. anything else? LSM says that is all i should need to do essentially. 97 c1500
  21. Soflanick911

    Where can i find a new OEM quality 3rd brake light?!

    thanks guys, do you all have any recommendations on how to clean a factory one?
  22. Soflanick911

    Where can i find a new OEM quality 3rd brake light?!

    mine is in good shape, just unfortunately the lenses are looking a little greenish. thank you guys, ill keep a look out for one a guess. has anyone tried the ebay red one? for 18 bucks shipped i suppose its worth a shot...
  23. Soflanick911

    Where can i find a new OEM quality 3rd brake light?!

    Hey guys, ive been looking for an elusive OEM style 3rd brake light. I seem to remember them being everywhere back in the day, now I can't seem to find one. Anyone know where i can find one? i am only seeing LED style ones. thanks, Nick
  24. Soflanick911

    If it were your truck ????

    zz454 if you're feeling nostalgic, Lt1 if you're feeling modern.... with a 75 mm snail...
  25. Soflanick911

    New guy, just want to see some static drops

    Man i wish my truck was that clean and red... my first chevy was a red 95 rcsb, mounting 20/22 speedways onto my recently aquired laguna green 97 on friday. what size tires did you go with? i was thinking 245/40/20s and 285/35/22s.

Latest posts

Members online

... and 14 more.
Total: 1,335 (members: 64, guests: 1,271)

Forum statistics

Threads
64,237
Messages
1,389,368
Members
51,195
Latest member
arboc40

Share this page

Top