Search results

  1. C

    Sliding rear window rattles/leaks air

    So what's stupid expensive? I have to put a towel on my bench seat every time it rains.
  2. C

    Cam upgrade??

    Maybe it is a mounting plate. But now i see everything is the same as the smaller ones. Guess I'm nervous I'm not going to have it running right when I do the swap. It's my daily and going to do the swap on the weekend.
  3. C

    Cam upgrade??

    What are your thoughts on a 454 TB. Do you need the base for it to work? I found one and the guy wants $50 no base. I've been tossing this cam around in my head also.. COMP Cams XFI 216/223 Hydraulic Flat Cam for Chevrolet Small Block
  4. C

    Cam upgrade??

    Your TB is that a punched out 454TB?
  5. C

    Cam upgrade??

    What do you think about this cam? Running MOD TBI all the bells and whistles, Vortec fuel pump, 64cc heads, 1.5 roller rockers and stock bottom end. Lunati 10120702LK Lunati Voodoo Cam and Lifter Kits | Summit Racing
  6. C

    LSA for a TBI

    So what flat tappet cam would yall suggest? Something stock converter friendly until I can afford a higher stall. I have a 700r so will the 4.3 s10 converter be good? INT--EXH Lift 300----188--135 400----227--164 500----244--181
  7. C

    LSA for a TBI

    I don't have a stock tune on it and can play with it some. I already have a custom chip in it and can play with the tuning. I want to say it has a 3.8something gear and no stall yet. I'm getting parts together to do the swap on a weekend.
  8. C

    LSA for a TBI

    I'm looking at putting some 200cc intake runner heads (64cc chambers)on my stock bottom end TBI motor. I've done all the TBI mods plus a 18lb spring. Vortec fuel pump, headers and a dual plane intake. I have a couple cams picked out but not sure whats going to work best.. Staying flat tappet...
  9. C

    What type of rims are on your truck

    275's will rub in the back. Roll the finder in and you will be good..
  10. C

    What type of rims are on your truck

    Can i get some specs on the rims and the tire size.
  11. C

    ZZ383 Fast Burn Heads/Cam/ValveTrain...

    What intake are you using?
  12. C

    5 x 4.75 Swap?

    So I ran all my RPO codes and it says my truck came with aluminum rims and a 5x4.75 bolt pattern.. What are the odds my truck has that bolt pattern.
  13. C

    291 heads on a 350 tbi

    Thank that’s what I was looking for. They have new hardened seats. I’m always open to options but stuck with the heads. So what intake would you recommend?
  14. C

    291 heads on a 350 tbi

    So both of y’all recommended more exhaust lift then intake. Why is that and what do you think about straight across the board on lift?
  15. C

    291 heads on a 350 tbi

    Fab up to exhaust and use the upper bars. That’s what I’m thinking for now.
  16. C

    291 heads on a 350 tbi

    Ok hopefully there are some old schoolers on here. I got a steal on some 291 rebuilt camel hump heads, intake(torker)and valve covers. Plan is to put them on my tbi motor and run tbi. I have already done all the bells and whistles to the tbi so it flows it’s max when needed. I have headers no...
  17. C

    Bump Steer Improvement Options

    Can we get some info from you? Whats your drop and what alignment numbers are you running? TY
  18. C

    Is this the transmission speed sensor and is it easy to pull out?

    Only tools required are channel locks, flat head screwdriver, hammer and a long socket. If you can't twist it out with the channel locks then get after it with the screw driver and hammer. One more thing before you reinstall the new one clean the area and put some lube on the O-ring. You may...
  19. C

    How to Put a Vortec Motor in a TBI Truck

    I should of worded that differently. What is the purpose of the bypass lines?
  20. C

    How to Put a Vortec Motor in a TBI Truck

    So where do the bypass lines run to is that for the heater?
  21. C

    How to Put a Vortec Motor in a TBI Truck

    So Question if I wanted to put Vortec heads on my tbi block I would just need the heads, 4 Barrel carb intake and adapter plate? Also I'm sure there would be some fabricating of lines involved.. I already have a Modified Throttle body with 18LB spring and a chip with EGR delete.
  22. C

    No overdrive in freshly rebuilt 700r4

    Try pulling the brake peddle up when it should be shifting into over drive. There is a switch connected to the brake peddle under the dash.
  23. C

    Alignment Numbers?

    No i did not. I was there for 2 hours and ready to go.. Thank you ill go back and see where I'm at and get it fixed. I'm assuming positive caster?
  24. C

    Alignment Numbers?

    So last month i did a 5/6 drop on my truck. DJM lowers and springs with all new suspension. Everything but the spindles. Took my truck and got an Alignment guy said he had to make some numbers up.. Blah Blah I'm still chewing the outside of my tires up but it drives straight. Does anyone have...
  25. C

    Finished drop, finally

    I found someone with stock shackles and just did a even trade. He got to lower his truck 2 inches and i got mine back to stock so i could do the axle flip. He paid his shipping and i paid mine.

Latest posts

Members online

... and 18 more.
Total: 1,683 (members: 68, guests: 1,615)

Forum statistics

Threads
64,247
Messages
1,389,779
Members
51,235
Latest member
ggddff

Share this page

Top