Search results

  1. ht89

    I Need More Fuel

    I found this info on... https://fuelinjectorclinic.com/hp-calculator # of Cylinders / 8 Fuel Pressure (psi) / 58 Injector full flow value (size) in CC/Min / 315 (30 lbs/hr) Engine Aspiration / Naturally Aspirated Duty Cycle / 80% Fuel Used / Gasoline Horsepower supported @ crankshaft: 443...
  2. ht89

    I Need More Fuel

    Thanks for the response stut... Yea, I just got the engine running... it's a new rebuild. I'm getting the codes after revving it a couple times to 2.5-3.5k RPMs. Is that considered a "load" on the engine? I'm very sure that "the cam and ECU tune are not optimized" and that "the ECU is not...
  3. ht89

    I Need More Fuel

    Thanks for the response RAWb... I'm getting the codes at idle/part throttle. I think the cold air intake and cam are making it run lean. So is it a higher pressure fuel pump that delivers more fuel? I don't really understand what the "lb" designation in regards to fuel injectors relates to. I...
  4. ht89

    I Need More Fuel

    I have a Gen 4 / 5.3 swapped into my 94 OBS. The DOD, VATS and downstream O2 sensors have been deleted from the E38 ECM. I paid a local guy who charges $500 for dyno tuning 200 for the bench service to get me up and running... He'll charge the balance of $300 when I bring the truck back for a...
  5. ht89

    Adding AUX to 88-94 Stock Stereo

    Here's my rig using the same switch and jack in post #1.
  6. ht89

    1989 Chevy 350 out- 1994 Chevy 454 in - got a question now

    The 94 wiring diagram shows that as a Dk Green wire with a C201A connecter. It's a serial data output (circuit #835) going to the DLC connecter, position J.
  7. ht89

    Media Blasted Aluminum Heads

    My heads were soda blasted and decked. Evidently it's the way to go.
  8. ht89

    Media Blasted Aluminum Heads

    I got my heads back from the machine shop and was surprised to see that they had been blasted. It's the first time I've had aluminum heads redone by a machine shop... is this normal?
  9. ht89

    I figured I'd introduce myself :)

    There is, was or should've been a counter-part patch of velcro on the inside matting surface of the outer bezel trim piece.
  10. ht89

    94 RCSB Off the Frame

    Can you please translate?
  11. ht89

    94 RCSB Off the Frame

    What can I replace this with? It's the (mostly deteriorated) mat between the interior side of the fire wall and the A/C-Heater box.
  12. ht89

    What Is It...

    ...and what can I replace it with? It's the (mostly deteriorated) mat between the interior side of the fire wall and the A/C-Heater box.
  13. ht89

    Oil Cooler Line Connections at the Radiator

    That's a perfect fit. Thanks man.
  14. ht89

    Oil Cooler Line Connections at the Radiator

    I've got a new OEM radiator for my 94 C1500 / 5.3 LY5 swap and want to use 6AN fittings to connect the engine oil lines to the radiator but I can't figure out what thread size the radiator inlets are. Does any one know the radiator Engine Oil Cooler thread dimensions for 1994 GMT-400?
  15. ht89

    What is everyone doing for headers?

    Those are for an 06-09 Trail Blazer. Soooo???.... will any long tube headers for the 88-98 trucks?
  16. ht89

    Which is Better?

    I'm currently planing out the exhaust system in a 94 SCSB with an 07-08 5.3 / LY5. I've narrowed my options as follows: A long tube set up with a 3" Y pipe and a single muffler. My local jurisdiction does not have smog check restrictions so I'm thinking I'd go with out cc and a single 02...
  17. ht89

    Long Tube Header & Y Pipes that work in OBS Trucks with LS Motors

    I'm in the process of a 94 SCSB, 2 WD frame off restoration. The sheet metal is at the shop for paint. I've got the frame back together with a 6 lug swap using the 14 bolt, light duty 2 WD 2500 truck rear end and front rotors. The 07 LS motor is installed w/o the cast iron exhaust manifolds. I...
  18. ht89

    C10 Door Handels

    On more than one occasion Crack Heads have tried to illegally enter my truck by jabbing a pry-bar under the bottom of the exterior handle trim and door. I want to customize an alternative to the OEM handle to discourage such behavior. I know about shaving the door and using a door popper, but...
  19. ht89

    How much has it been lowered?

    https://www.wheel-size.com/size/chevrolet/impala/1994/ The off-set (ET) on the Impala wheels is 6mm. The off-set (ET) on stock 94 Silverado wheels is 10-13mm.
  20. ht89

    Does Anyone Know...

    oh, i didn't realize i was looking at an S10 Blazer. Thanks for the corrective vision.
  21. ht89

    Does Anyone Know...

    if an interior (i.e. dash board) from a 94 Blazer swap into a 94 c1500?
  22. ht89

    Missing Numbers

    I never thought of that.
  23. ht89

    Missing Numbers

    How normal is it that there are no numbers on the left front of an engine block? The casting number on the right rear is 10243880.
  24. ht89

    I'm in need or Education

    Hey moderator... please delete this double post.
  25. ht89

    I'm in need of some Education

    I don't know @#$% about engine performance... so I can't understand why someone would put 305 TBI heads an a 5.7 Vortec (10243880) block? The motor (none of which is original to the truck) is out of a 94 SCSB Silverado, 8th digit VIN = K. I picked it up for an LS swap / frame-off restoration...

Latest posts

Members online

... and 25 more.
Total: 1,418 (members: 75, guests: 1,343)

Forum statistics

Threads
64,202
Messages
1,388,764
Members
51,136
Latest member
ponchis323

Share this page

Top