Search results

  1. Cole Chambers

    Throttle Body Modifications

    What does the relearn do?
  2. Cole Chambers

    Throttle Body Modifications

    The torx was turned all the way in before I did the mod so i couldn't turn it anymore. And no, the idle is still the same as it has always been.
  3. Cole Chambers

    Throttle Body Modifications

    Here is what I meant by the whole zip tie deal.
  4. Cole Chambers

    Throttle Body Modifications

    So basically, when my tb plate closed all the way the pedal became almost as some called it an "On-off switch". While playing with the butterfly I noticed there was a small torx where the top of the butterfly rested, so in order to remove the stiff stop in the pedal, i but a zip tie around the...
  5. Cole Chambers

    Throttle Body Modifications

    I'll try to get you a picture later on around 3:30
  6. Cole Chambers

    Throttle Body Modifications

    I decided to take a risk today and cut the "flap" off of my throttle body blade. After getting everything back together, I noticed that the gas pedal was extremely stiff and almost made it impossible to drive. However, there was a great amount of improved acceleration (NOT HORSEPOWER). Upon...
  7. Cole Chambers

    The Body Lift Thread

    How did you bring the step bars up with the body lift?
  8. Cole Chambers

    The Body Lift Thread

    I'd been searching for another truck with that sort of lift and 315's but never found one. Your truck looks sick man.
  9. Cole Chambers

    The Body Lift Thread

    Just in case anyone was wondering.. It is possible to fit 315/75r16 on 16x10 wheels if you have a 3 inch body lift and adjust the torsion bars a little. I have a two inch block in the rear and have the torsion bars up 3/4 of the way. I had to trim the lower plastic valance of the bumper at an...
  10. Cole Chambers

    The Body Lift Thread

    Thats what ive seen. I don't know if this issue would be a big one. I have a vortec.. but i'm pretty sure that's why they say they won't fit the diesels. But they also might, i'm sure the is someone that has but a body lift on a diesel model.
  11. Cole Chambers

    Torsion Bar crank

    So how bad is your ride? And also, have you had any issues with the front end parts wearing out?
  12. Cole Chambers

    Not the normal brake light issues.

    I’m having a problem with my 97 K1500. I had a tailgate brake light strip that suddenly started displaying the incorrect sequence of lights. When I press the brake the third brake light lights up like fine, but the actual tail lights light up the wrong bulbs. My rear turn signal lights up when...
  13. Cole Chambers

    The Body Lift Thread

    How much did you have to cut from the back of the fender?
  14. Cole Chambers

    The Body Lift Thread

    3 inch body lift and 285/75r16
  15. Cole Chambers

    LED Gauge Install

    How hard was it to remove the dash to get to the bulbs?
  16. Cole Chambers

    35s with t-bar crank and 3 inch body lift

    If you crank the torsion bars all the way you’ll get bad angles. Mine are up 3/4 of the way and you can tell there’s a slight angle but not enough to destroy the front end
  17. Cole Chambers

    The Body Lift Thread

    My 97 k1500 has a 3 inch body lift, 2 inch block and torsion bars cranked. I’m running 285s on my 16x10 ultra 164s. Could I fit 35s without cutting much of my fender?
  18. Cole Chambers

    35s with t-bar crank and 3 inch body lift

    I have a 97 k1500 with a 3 inch body lift and a 2 inch axle block and torsion bars cranked. I’ve been wondering if anyone else has or knows if you can fit 16x10 wheels with 35s without doing a lot of cutting on the fender. Cutting the bumper and valence doesn’t bother me any but rather would...

Latest posts

Members online

Total: 1,388 (members: 24, guests: 1,364)

Forum statistics

Threads
64,253
Messages
1,389,890
Members
51,246
Latest member
robert2386

Share this page

Top