Search results

  1. 9

    radio buttons

    Hi everyone, are the buttons on the radio and heater control supposed to light up when the headlights are turned on? If so none of mine are on. What to look for if they are supposed to light up. Thanks
  2. 9

    Rear bounces when towing

    Thanks for all the advice. will open up the trailer and move as much to the front as possible and check my tounge weight. This is not a bolt together trailer tounge so no holes to get out of round. What is a universal clamping hitch. trailer takes a 2 inch ball and that is what I have on the...
  3. 9

    Rear bounces when towing

    May only have about 200 lbs in bed when I tow this camper. will have to check out the tounge weight. Shocks are new all four corners. I found a bracket that bolts the hitch and draw bar tight to each other, going to try this, but will take all suggestion and try them. We have a big scale at work...
  4. 9

    Rear bounces when towing

    The truck is a 1500 rcsb. Front Is 2in lowering springs and the rear is with shackles. Sorry that I did not put that in. Was told that it could be the draw bar bouncing in the hitch.
  5. 9

    Rear bounces when towing

    Hope someone can help. I have a popup camper that weighs 2600 lbs. When I start from a stop it feels like I am bottoming out in the rear. Any idea's what can cause this. I have new shocks all around. The truck is lowered 2 inches all around so should still have plenty of suspenion travel.
  6. 9

    new engine

    So do I need ro get a computer and prom for a 350 to make ir run right?
  7. 9

    new engine

    Thanks Schurkey, so I need to get injectors and a knock sensor and a computer for a 350. I dont see an ESC module on my truck now.
  8. 9

    new engine

    Hi every one. I will be replacing the engine in my 1994 scsb with a 305 in it to a 350 crate engine. What all will i need to make this run? Are the injectors, computer and everthing else the same? Thanks for the heip.
  9. 9

    rear brake problem

    Sorry for not repliying back on this problem,been working so much , I finally got some time to pull the driveshaft and clean and grease the splines. That was about 2 months ago and have not had this problem since.Thanks Schurkey for pointing me in the right direction.
  10. 9

    radiator trans cooler

    Thanks for the info,I will be putting a trans temp guage on it .
  11. 9

    radiator trans cooler

    On my 94 rcsb the transmission cooler in the radiator was bypassed and an auxillary cooler installed. I will be pulling a camping trailer that is 2300lbs empty. Will this be a problem or should I get a new radiator and use the oe cooler and auxillary. Not sure why it was bypassed. Thanks for any...
  12. 9

    rear brake problem

    The rear brakes were done about a year ago, it also did this before they were changed so I will check out the driveshaft. Thanks
  13. 9

    rear brake problem

    Sorry about that . It is a 1994 rcsb 2wd,
  14. 9

    rear brake problem

    When I brake hard and come to a complete stop at a red light then release the brake a little the back end of the truck seams to make a clunking sound as if the shoes bind up. Anyone else have this same problem.
  15. 9

    No brake lights

    I wae the turn signal switch
  16. 9

    No brake lights

    Thanks Tdean. I will check these out today.
  17. 9

    No brake lights

    I have no brake lights,I put in a new switch and turn signal switch, I have no power to the brake light switch or fuse with the ignition off but do with it on. I checked the wiring back to the lights and do not see any broken wires. Please help
  18. 9

    engine idles high

    Checked all fuses then pulled the ecm out and found corrosion on the terminals, cleaned with electrical contact cleaner, Trucks runs great now.
  19. 9

    engine idles high

    A freind has a 1993 with a 350 w/a 4l60e trans. It started to idle high, shift hard and stall sometimes. He chainged the iac, and tps but did not work. I hooked up my scanner and it would not connect. all fuses are good. Any idea's to look for.
  20. 9

    Front springs won't seat in the control arm pocket

    When I did my springs I used a piece of 1/2 inch all thread and 2 metal plates. i drilled a hole in each plate a little bigger than the all thread. I welded 1 nut to the all thread put a plate on then unbolted the control arm set the spring in it then ran it up through the shock put the 2nd plat...
  21. 9

    Black Dog - 94' C1500 Vrtc 5.7 NV3500

    I just read your whole thead. Your truck looks great. My question is what is the quick ratio steering gear box that you used? I need to chande mine as it has to much play and want a quick ratio.
  22. 9

    tbi to vortec

    Thanks for the replies. I see the adapters come in a forward mount and a rear mount for the tbi. What is the differnce?
  23. 9

    tbi to vortec

    thanks Eric
  24. 9

    tbi to vortec

    Just got 1998 350 vortec engine for my 94 1500 with a 305. What is a good intake manifold to get. I want to stay with the tbi. Thanks for any help.
  25. 9

    steering box

    Will a zq8 steering box from an s19 fit a 94 1500.

Latest posts

Staff online

Members online

... and 26 more.
Total: 1,969 (members: 76, guests: 1,893)

Forum statistics

Threads
64,343
Messages
1,391,677
Members
51,454
Latest member
Wentworthcj2706

Share this page

Top