Search results

  1. M

    Code 41 coming up

    Hello all, Finally got rid of the monies gauges on my 90 5.7 step side truck and now I’m able to get codes out of the truck via blink code. That being said I’m looking at code 41 cam sensor circuit fault, igntion control circuit fault and tried to do a bit of digging into it have not really...
  2. M

    88-91 to 92-94 cluster upgrade

    Hello all, I am wanting to swap out my moonies the cluster itself is starting to fail, having over 500,000km on it I figure it’s time for replacement. I have 2 gauges from the 92-94 sitting in my shop and have connectors, I still have the drac to remove but that is minor. Right now I’m...
  3. M

    Restore of a rcss

    Here are finally some more pictures of the truck, let me know if anyone else wants to see anything else. Or have any questions. Sent from my iPhone using Tapatalk
  4. M

    Restore of a rcss

    As soon as I can get back from work during the day light I will get some more pictures inside and out for you. As for the engine it’s just a 350 that I resealed, reringed and new bearings, the block itself was is in great shape just honed out the block. Sent from my iPhone using Tapatalk
  5. M

    Restore of a rcss

    Well it’s been a long time coming but it’s almost complete, just needs to get the ac charged up I’ll do that later date at work and get an alignment in the next week or or but it’s ready to roll seems to be running good and if I do say so my self looks pretty good also. Sent from my iPhone...
  6. M

    Getting stuff ready for primer and paint

    You don’t think the clear on the bed line will make it too slick? I’m about at the point to finish the top side of my box and do thyou bed liner. I sprayed the bottoms of the doors and rockers of the cab in rockguard and paint and clear and the finish is very slick to run your hand across I’m...
  7. M

    90 350 service engine soon flashing while running

    I believe I may have found the possible issue, with the flashing. It was doing so very faintly. I figured I would try putting a battery charger on it. With the charger it now stays on solid so I’ll let it charge for a while and see what happens, I do believe I will be getting that adapter...
  8. M

    90 350 service engine soon flashing while running

    I don’t have one from the back of the head to the fire wall, I do have one front block to the battery, I’ll add another ground to the back of the head to the fire wall see if that changes anything also Sent from my iPhone using Tapatalk
  9. M

    90 350 service engine soon flashing while running

    Catalyst? I assume you mean cat converter? This truck doesn’t have it and is not required to have it, it has stock manifolds (new) new y pipe, 3 in to the muffler and dual 2.5 out to the tail pipes Sent from my iPhone using Tapatalk
  10. M

    90 350 service engine soon flashing while running

    All grounds are all new for battery to block ,battery to cab, frame to cab, battery to frame. I will check all the grounds at the thermostat and double check my work and am looking for a scan tool that has obd1 ability all of mine that I have are not able to do obd1 Sent from my iPhone using...
  11. M

    90 350 service engine soon flashing while running

    So I tried to get blink codes this morning again after the 3 1-2 combo I got 5-1-4-1-3 and the three really faded out that you could just see it and have good 12.6 volts when doing it Sent from my iPhone using Tapatalk
  12. M

    90 350 service engine soon flashing while running

    It’s a 1990 gmc k1500 with a stock 350 Sent from my iPhone using Tapatalk
  13. M

    90 350 service engine soon flashing while running

    Hello all, Little but stumped right now with my truck, I recently installed a freshened up 350 has 150 compression across the board, has all new sensors and plugs wires etc, Recently set my timing with the wire unplugged to 0 or very close to it, shut down the truck plugged the wire back in...
  14. M

    Wiring

    Here you go Sent from my iPad using Tapatalk
  15. M

    Full fuel line replacement! What would you do?

    It’s a pain to do the ends but I went with nylon fuel lines Sent from my iPhone using Tapatalk
  16. M

    90 5.7l confused on a single wire connector

    Ok I’ll take a look at a wiring diagram thank you Sent from my iPhone using Tapatalk
  17. M

    90 5.7l confused on a single wire connector

    That’s what I figured so I should be safe to hide that wire and pigtail away in the loom? Sent from my iPhone using Tapatalk
  18. M

    90 5.7l confused on a single wire connector

    But more than one knock sensor? Sent from my iPhone using Tapatalk
  19. M

    90 5.7l confused on a single wire connector

    Hello there, I have my stepside that I’ve ripped all apart and starting to go back together redoing a lot the wiring, found this single wire connector looks like a knock sensor but that’s already connected and done it comes up near the Ac and intake out of the main harness will include a...
  20. M

    Restore of a rcss

    Bit more of an update now, a few more things have happened the cab has seen some primer and little bit of putty and finally paint and the motor is starting to go back together now and block is also painted although there was a major screw up with the colour I wanted to be and how it ran out of...
  21. M

    Restore of a rcss

    Sent from my iPhone using Tapatalk
  22. M

    Restore of a rcss

  23. M

    Restore of a rcss

    I really haven't done a update In quite a while now but here we go, the last time I posted I'd gotten everything but the cab off of the frame. This fall we last my father to a very sudden heart failure and was a very big loss to my family and myself he guided me into everything I've done...
  24. M

    Torsion tubes going to lower control arms

    It does unbolt but to get the key out you either beat it out or cut the key off or cut the crossmember, going to try working on it tonight in between the jets hockey game. Will update how I make out Sent from my iPhone using Tapatalk
  25. M

    Torsion tubes going to lower control arms

    Over the years riding around in canada with the salt on the roads there is alot of rust and grim in ther seizing the bars; I was going to try and just cut a chunk out of the key to help seperate it; otherwise i could cut out the crossmember and then cut the key with a grinder and weld that frame...

Latest posts

Staff online

Members online

... and 5 more.
Total: 1,319 (members: 55, guests: 1,264)

Forum statistics

Threads
64,303
Messages
1,390,877
Members
51,363
Latest member
Ajfazio

Share this page

Top