Search results

  1. laidbackbigun

    Dual ad244 wiring

    Juat finished hard install on a 2nd ad244 alt. Can i just run the "I" wire to the same brown wire my 1st alt is connected to? I believe its the factory gauge wire on a 1995 Tahoe.
  2. laidbackbigun

    Nbs style dash bezel into 96 dash

    Okay so the double din dash bezel from a 03 and up is supposed to work in a 1996? I had read and seen that it did on facebook but now the post is gone. Anyone got any insight?
  3. laidbackbigun

    Thermostat housing

    Looking to replace my thermostat housing with a chrome one given to me for free. It looks the same but guy says my tbi intske uses a different style housing and his is for a old sbc intake.
  4. laidbackbigun

    Dual fuel cells

    I didnt know where else to put this thread. Got two 8 gallon fuel cells for the bagged tahoe with limited space i could not fit one single 15 gallon or 20 gallon but two 8 gallons with 1/2 inch space between them works awesome. My question is whats the best way to plumb them. When you search...
  5. laidbackbigun

    Confused and lost.

    1st things 1st. Its a 1995 Tahoe with auto trans 2wd. Yeah a 1995 the stupid year. Thinking of swapping a crate 355 from speedway in. Which means carb. How can i get this engine to work with that stupid one year only transmission? Ive searched and am confused. So if someone could break it...
  6. laidbackbigun

    Issues with pedal while running

    Okay a little run down 1. 1995 tahoe removed abs junk and replaced with a proportioning valve from a 1992 c1500. 2. Replaced all lines front and rear, replaced all brake components except master cylinder and brake booster. 3. Disc front drums rear. Heres the issue. Engine off pedal is firm...
  7. laidbackbigun

    Accessory mounts.

    Kinda off the wall question. Can i use the vortec style front accessory mounts on passenger side and tbi style on driver side to mount my alternators and the like. I wanna run dual alts and have a free set of vortec style mounts to use. Quick rundown; 1. Take off ac bracket for tbi and install...
  8. laidbackbigun

    Ad244 beat a dead horse

    Okay ive been searching and im lost in the sauce. 95 tahoe with one brown wire with squarish pigtail going into a ad244 roundish plug. How do i wire it? I see no definate answers on the wiring just about mounting physically which is already done. Final stage and i dont know how to finish. Thanks...
  9. laidbackbigun

    Lost on Axle ratio.

    1995 Tahoe 2wd 4 door woth 5.7tbi. I cant refer to rpo codes as dash was swappes by po and no numbers match anything. What was the typical ratio for the rear end. Im having some no movement problems. Let me explain. Truck was almost completly gone thru tune up wise and fuel system. Runs very...
  10. laidbackbigun

    Wiring in a seperate led brake light.

    How would i wire this into the factory wiring to make it work. I know this sounds like a noob question but with one bulb being brake light, running light, and turn signal i dont want it to work but only on brake lights thanks
  11. laidbackbigun

    Difference in tach signal

    Okay while troubleshooting my high voltage problem i have noticed that all 3 clusters i have gotten the tach is wild. My tac for the 95 reads just fine but when i plug in the cluster from the vortec trucks the tach runs way high and wild. Is the tach signsl different? How do i rectify this?
  12. laidbackbigun

    High voltage

    Issue im having is the stock gauge in cluster is reading 18 volts tripping the battery light when ibput a voltmeter on it says 14.1 my aftermarket gauge says 14.1 Now i tried a different cluster and same thing. Anyone know what it might be its a 1995 5.7 tahoe with tbi
  13. laidbackbigun

    Beginning a vortec build.

    Got a relatively low mileage gm crate motor from a 2001 workhorse route truck. Bread truck for those wondering. Its a vortec 5.7 same as a c1500 or the like. It was pulled because the tech removing the leaking exhaust manifold broke a stud then drilled to far into head. Burst a water journal...
  14. laidbackbigun

    95 Tahoe wiring issue

    Redoing the hack job rear half wiring. I have figured out most of it with the help of a Haynes manual for a pickup. I have found a large orange, a large blue, and a small white that were cut and left hanging. I have no clue what they went to. Any help is appreciated.
  15. laidbackbigun

    Grounded 4 Life One Day Slam Bristol PA July 8th

    Grounded 4 Life is holding their show One Day Slam its always a huge turnout and good time. Ill be there with my club Xtreme Dimensions feel free to stop by.
  16. laidbackbigun

    1995 tahoe tailgate plastic

    okay so i have a 1995 tahoe which has the tailgate rear. what does the plastic look like that covers all the holes in the inside of tailgate. or isn't there any? i know gm had to cover it somehow. i can't find a tailgate tahoe in any yards near me to either get the piece or see what it even...
  17. laidbackbigun

    Sensor diagram

    Looking for a external shot or diagram of all sensor locations for a 1995 5.7l tbi tahoe. Have found a sensor melted and hanging down on passenger side don't know what it is or where it goes. Google was of no help. Thanks.
  18. laidbackbigun

    Knock Sensor

    Okay so this 95 tahoe has the last year tbi. i got it and the knock sensor is unplugged and sitting in the block. i can't find the wire that runs to it. Can someone point me in the direction that i can snag that wire and wire it up. It runs fine without it which kinda goes against the purpose...
  19. laidbackbigun

    Hard to find seal

    The rubber isolator seal that sits on spindle that the rotor assembly pushes up against. I painted my drop spindles and lost these somewhere along the line. Anybody know how to find them or if they truly are needed?
  20. laidbackbigun

    Blueberry Yum Yum

    It's the name of my new build. 1995 4 door Tahoe previously bagged horribly about 10 years ago. Apparently it was a pretty popular truck in the Florida Georgia area for a long time. Now it's up here in PA with me. Lays running board and frame hump on 24s. I'll just slap the older pics in here...
  21. laidbackbigun

    Deleting some wiring.

    Okay so not sure if in right area but here goes. 1995 tahoe. 5.7l anyone see any issues with deleting all the abs and airbag stuff off of the underhood harness. Im not saving any of it and its a custom build. Not street legal in the slightest ha. I'm just gonna snip it and heatshrink the ends...
  22. laidbackbigun

    Deleting some wiring.

    Okay so not sure if in right area but here goes. 1995 tahoe. 5.7l anyone see any issues with deleting all the abs and airbag stuff off of the underhood harness. Im not saving any of it and its a custom build. Not street legal in the slightest ha. I'm just gonna snip it and heatshrink the ends...
  23. laidbackbigun

    Bag cup height

    Okay so it's a long shot but here goes. 95 tahoe Michigan metal works flat plate arms on a slam re7 bag what does the upper bag cup height need to be on 255/30r24. Thanks guys.
  24. laidbackbigun

    Obs Tahoe vs Obs C1500

    How truly different are the front frames. I just acquired a 95 Tahoe and it's bagged but needs help. Just wondering if things like shock replicators for c1500s will work. Ie bolt in art style relocators.
  25. laidbackbigun

    Engine wiring harness.

    I recently purchased a 1995 Tahoe that had been modified with air ride and other things. The p.o. chopped up the factory engine harness pretty good. Does anyone know where or if anybody sells a underhood harness I can swap out with my hacked up one?

Latest posts

Members online

... and 13 more.
Total: 1,418 (members: 63, guests: 1,355)

Forum statistics

Threads
64,238
Messages
1,389,414
Members
51,200
Latest member
jsheets1

Share this page

Top