BowtieJC
I'm Awesome
I need a blue 1996 dash bezel , no cracks and all clips good . Mine had broken headlight switch clips broken do switch is loose
Gmt400 parts
- Thread starter thz71
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
HotWheelsBurban
Gotta have 4 doors..... Rawhide, TOTY 2023!
Can you get me a measurement on what length you need? I have to go to my garage building where these are tomorrow, and I will see what lengths I have. I also have several of the end plates too....
98chevy2500SS
Specializes in Accessories 101
I can't remember what length they would need to be, I had found some running boards at a j/y a couple months ago from a 2000 NBS truck and it looks like they'll fit with some modification.
HotWheelsBurban
Gotta have 4 doors..... Rawhide, TOTY 2023!
Well that's probably a lot easier than me shipping you some from Houston, Texas... cheaper too!
We had a bunch of different sizes because Dad was going to put them on a square body Burb. Then when we got the 90 R2500 3/4 ton that was already a tall boy, those boards would get air under them and make it handle squirrelly in much wind. So he kinda got away from that plan....once I got the front end fixed on that truck, though, it was not as bad about that.
We had a bunch of different sizes because Dad was going to put them on a square body Burb. Then when we got the 90 R2500 3/4 ton that was already a tall boy, those boards would get air under them and make it handle squirrelly in much wind. So he kinda got away from that plan....once I got the front end fixed on that truck, though, it was not as bad about that.
herkyhawki
Newbie
1998 5.7L with Auto trans K1500.
There are two braces(brackets) from the motor mounts to the bottom of the bell housing. After installing new GM transmission, the brace on the drivers side has gone missing. Looking fo a source to get one of these, as I'm concerned if I end up with a problem, my warranty could be voided. I have the plate at the motor mount for the bar to connect to , just need the bar and bolts.
There are two braces(brackets) from the motor mounts to the bottom of the bell housing. After installing new GM transmission, the brace on the drivers side has gone missing. Looking fo a source to get one of these, as I'm concerned if I end up with a problem, my warranty could be voided. I have the plate at the motor mount for the bar to connect to , just need the bar and bolts.
MrPink
Bainisteoir Páirteanna
flat landah
Newbie
Looking for a shift tower from a '94 k1500, nv3500 trans. rpo code mg5
Similar threads
Members online
- Schurkey
- captainamerica454
- Gus87
- mxmxmc3000
- Nephrodoc
- Griffin
- termite
- Caman96
- shaneroze
- y5mgisi
- name
- movietvet
- scott2093
- Erik the Awful
- Giantnic
- Hipster
- Cv100902
- Keeper
- OffroadZ71
- Bad choices
- Masterofbopits
- Black98Burb1500
- JAR724
- Jroctizzle
- L31MaxExpress
- vince72
- maddux1037
- HotWheelsBurban
- Brian71583
- Arthurius
- AK49BWL
- PlayingWithTBI
- unknwnzz
- 0xDEADBEEF
- grampadirt
- gmt400gmc
- 618 Syndicate
- Peavey
- Dave69
- rzr6-4
- heyitzjoel
- Terbro
- CrustyC1500
- johnckhall
- Mg guy
- reggie337
- Cr916
- Rock Hard Concrete
- Creek
- mdnky