Sway bar issue with DJM control arms
- Thread starter Jim2029
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
sewlow
Bitchin' Stitchin'
Truck sitting on the suspension or up in the air?
Those mounts do look like they are out 180*.
Doesn't look to be a robot weld. Somebody not paying attention?
2" or 3" arms?
Those mounts do look like they are out 180*.
Doesn't look to be a robot weld. Somebody not paying attention?
2" or 3" arms?
It was up in the air. I even compressed that side with a floor jack and it made very little difference. This is the 4" front kit (Lwr ctrl arms and coil springs). The mounts in the pictures on the site look just like this.
This truck does (did) have the heavy duty RPO code for the shocks from the factory. Doin't know if the sway bar is bent differently because of that. I'll be getting ahold of DJM once again tomorrow. I'm wishing I never went down this road at this point. The truck will be getting an alignment this week and put on the road regardless of the sway bar being installed, I have some stuff to move.
This truck does (did) have the heavy duty RPO code for the shocks from the factory. Doin't know if the sway bar is bent differently because of that. I'll be getting ahold of DJM once again tomorrow. I'm wishing I never went down this road at this point. The truck will be getting an alignment this week and put on the road regardless of the sway bar being installed, I have some stuff to move.
outlawten5
I'm Awesome
Mine looks like that as well. I just cranked them down. Also looks like they aren't powder-coating their stuff anymore. How does the toe adjustment look? My truck was severely toe-out after installing their control arms. After a phone call I was told I would have to modify my tie-rods and sleeves to get the toe back in spec. Would have been an important note to add to the instructions.
Evan el bono
Newbie
Hey jim2029
How’s is your truck with the Djm 4” control arms and springs now how where you happy with the kit? I just am in the middle of putting it in my truck it’s been a huge pain.. terrible instructions... any help would be appreciated thanks
How’s is your truck with the Djm 4” control arms and springs now how where you happy with the kit? I just am in the middle of putting it in my truck it’s been a huge pain.. terrible instructions... any help would be appreciated thanks
shortchevy
I'm Awesome
- Joined
- Jan 17, 2011
- Messages
- 742
- Reaction score
- 113
This is how mine look, 7 years with no issues... my only suggestion is make sure you lube the sides of the LCA bushings or they squeak like crazy
someotherguy
I'm Awesome
Wow...to hell with dropping using DJM lower arms. I'm not a fan of control arm drops anyway. Springs & spindles is where it's at
Richard
Richard
Casey916
OBS Enthusiast
Yay same here whays the deal.. Mine do that 2
Similar threads
Members online
- Drunkcanuk
- Smeals
- HotWheelsBurban
- 95YardArt
- Calamari
- Nad_Yvalhosert
- 99xcss4
- Tritech
- maviles
- Hipster
- ccreekfreddy
- movietvet
- scott2093
- Sean Buick 76
- joeminer81
- rosert
- EDburb
- SlamTheMan
- 454cid
- 1998_K1500_Sub
- Luke_P
- Aqua-pig
- maddux1037
- John Moore
- Eldardra
- AlohaOBS
- Tonyz28
- YNGTMR
- grampadirt
- gbw83
- JPVortex
- Rgiberson85
- 98sub1500
- Kwades
- Tims 97 Chevy
- PM18S4
- Rich Suhanov
- T1najero
- ryansusername00
- 89bowtie
- jbphelps76
- BigBlueWhale
- JDT212
- cool99846
- Nephrodoc
- 97burbun
- JAR_19
- Shane B
- Yeee6
- Suzukin92