-
-
VVTSilverado posted the thread 1996 k1500: How do I disconnect the seatbelt connector? in Audio + Electronics.Seems like it should be obvious, but I can't figure out how to disconnect the driver's side seatbelt warning connector to test it. It...
-
VVTSilverado replied to the thread Torque spec for 1996 Silverado K1500 4WD Hub to Steering Knuckle Bolts?.I got the truck on the road today -- nice to hve it back again. For the road test I threw a fishing rod in the bed, and drove a couple...
-
VVTSilverado reacted to someotherguy's post in the thread Torque spec for 1996 Silverado K1500 4WD Hub to Steering Knuckle Bolts? with
Like.
While I've found some helpful info in youtube videos, I don't like to rely on them. It's too easy to trust people that may not be... -
VVTSilverado replied to the thread Torque spec for 1996 Silverado K1500 4WD Hub to Steering Knuckle Bolts?.All sealed up this evening: new hubs, calipers, pads, rotors. Hub bolts to 133, axle nuts to 165, the abs sensors work, ABS light went...
-
VVTSilverado reacted to scott2093's post in the thread Torque spec for 1996 Silverado K1500 4WD Hub to Steering Knuckle Bolts? with Like.
Frustrating for sure..... FWIW my 93 torque specs are the same 133 lbs for the hub to knuckle bolts
-
VVTSilverado reacted to 1998_K1500_Sub's post in the thread Torque spec for 1996 Silverado K1500 4WD Hub to Steering Knuckle Bolts? with Like.
^^^ Ditto But I have found mistakes in the FSM before, so there's that.
-
VVTSilverado reacted to GoToGuy's post in the thread Torque spec for 1996 Silverado K1500 4WD Hub to Steering Knuckle Bolts? with Like.
You can't go wrong with The OE service information first. Then see what any other " experts" advice goes to.
-
VVTSilverado replied to the thread Torque spec for 1996 Silverado K1500 4WD Hub to Steering Knuckle Bolts?.Thanks Nitro Junkie. That did it. I went with the 133, and dry. Now puttin in the new rotors and calipers...... Might have this thing...
-
VVTSilverado reacted to 1998_K1500_Sub's post in the thread Torque spec for 1996 Silverado K1500 4WD Hub to Steering Knuckle Bolts? with Like.
The same "133lbft" spec shows up elsewhere in the 1998 FSM, e.g., here:
-
VVTSilverado reacted to 1998_K1500_Sub's post in the thread Torque spec for 1996 Silverado K1500 4WD Hub to Steering Knuckle Bolts? with Like.
My notes from when I replaced mine on my 1998 say 133lbft. My notes say: See Helm manual, Vol 2, pg 3-74, “Wheel Hub, Seal and Bearing...
-
VVTSilverado posted the thread Torque spec for 1996 Silverado K1500 4WD Hub to Steering Knuckle Bolts? in Street Chat / Timeslips.I'm replacing the front hubs on my 1996 Silverado and I'm seeing bolt specs all over the place. One Youtube video says the bolts don't...
-
VVTSilverado replied to the thread Tailight Problems.Just to follow up... I used alligator clip leads to first connect the black wire to frame, and yes the tail lights all then worked. I...
-
VVTSilverado replied to the thread Tailight Problems.Wow absolutely thorough explanations diagrams and help from you all! What a great group. Hope I can return the favor some time!
-
VColor diagram and ground locations. These diagrams are non OE. Hope it helps.
-
VGreetings VTSilverado, Snagged the following G401 wiring distribution and physical location illustrations out of the '96 FSM. (See...
-
-
Loading…
-
Loading…
Members online
- jblennis
- Papikev252
- Kwades
- 1991cheyenne
- JimB1500
- Schurkey
- rebelyell
- caw_86
- Stormbringer
- Chogf15
- Laredo
- Brenbren
- Turbo86
- bluex
- Charlesteneows
- 96ChevyC1500
- PlayingWithTBI
- movietvet
- Jack Albert
- Minn95Dually
- gasburner
- Robert Edgar Holt
- 99xcss4
- TheRoninBlack
- dantaeT
- Scooterwrench
- dotwell69
- PolarBear
- smithgunboy
- rzr6-4
- Obs2500hd97
- 0xDEADBEEF
- omggopher
- smokymtn65
- the_elegant_fox
- mauser98a
- Orpedcrow
- rider927
- Lockheed12a
- Shocker53
- Thor
- Andyoli
- Alteca
- Cuckfield
- Tintai
- JuiceZ71
- 454cid
- Rock Hard Concrete
- nneel3167
- 67chevymechanic