Recent content by Mhenry1282

  1. M

    4.3 to 383 Blueprint Sniper EFI

    What headers are you running now? I'll be orderinn their 400 soon, can't wait to toss that tbi 350! Ordered the edelbrock pro flo in Jan, should be here this month or next. Needto get some headers figured out soon
  2. M

    Fiberglass Tonneau Cover for Sportside Bed

    I'm curious as well, I've looked at rally tops. Pics, at least thoughts on it?
  3. M

    Door cloth

    Does anybody know of anywhere that sells the factory pattern to redo the doors? Looking for the grey on a 90 Silverado with factory power. Really just needs new fabric, I can't seem to find any.
  4. M

    4l60e vette servo install

    I couldn't get situated right to hold the prybar and work the snap. 4/6 drop, and I didn't jack the truck up much to get under it.
  5. M

    4l60e vette servo install

    I just did mine, and found I needed a third hand to hold the servo in when installing the last snap ring. Tossed a cargo strap around the trans, being careluf to avoid the electrical harness and speedo cable, then stuck a deep well socket in the cup on the servo housing. Snuggled it down and the...
  6. M

    Long tube mid pipe

    Thanks for the input. I've always preferred the sound of an h pipe over an x, I'll probably go that route with dynomax super turbos. Nice deep tone, but not too loud.
  7. M

    Long tube mid pipe

    This motor won't see a whole lot more, maybe a top end. Got the headers for $40, so I figured I'd grab them. When I eventually do a new motor, I'll get a good set of headers. I was thinking of 2.25 or 2.5" with an H pipe for this setup. They sell def, and egr delete kits for off-road diesels...
  8. M

    Long tube mid pipe

    Searched and haven't found one, is there an off the shelf h or x pipe for long tubes? 90 rcsb with 5.7 tbi, cold air intake, and hypertech chip. Picked the headers up used and cheap, heads hopefully in the near future. I'd prefer an h pipe if one is available. Don't have an exhaust shop close...
  9. M

    Custom Painted Fiberglass Tonneau Covers

    Can anybody with an ARE bed cover send some detailed pics of the frame and hinge? I recently got one, but there was no frame work for it. Trying to find out how they were originally made before I try to fab one
  10. M

    Jegs spike wheels on the obs

    Awesome, thanks! Any fitment issues?
  11. M

    Jegs spike wheels on the obs

    That's about identical to mine! 90 white stepside. What are the backspacing and offset of the wheels, if you don't mind? I'm looking to do a similar setup on mine, but probably 15's up front. Worried about fitment as I have a 4/6 drop as well
  12. M

    Swap Meet Slam

    Where did you get your door panels from, or did you make them? They look great, and I'm needing a set!
  13. M

    Anybody use limbotics step shaver kit?

    Finally found a decent stepside bed for my truck, 1990 Silverado. It needs paint, and a little fiberglass work, but not too bad. Thinking of shaving the rear steps while getting the paint done, along with shaving the tailgate handle. Does anybody have an idea of what to expect cost wise from a...
  14. M

    4-6 drop with fats and skinnys

    Truck currently
  15. M

    4-6 drop with fats and skinnys

    I've searched for a while, and can't find a positive answer, although I'm sure it's on here. I have a 90 Silverado with a 4/6 drop. Looking to go with 15x10 or 12 rear and probably 15x4 or so on the front. What specs should I be looking for? Wanting to go with a 5 spoke, like centerline or...
Top