Recent content by Madison Mehlhose

  1. Madison Mehlhose

    Voltmeter Bounce

    https://imgur.com/gallery/UAy1550 I’d be willing to bet my bounce was slightly worse than anyone’s haha. Anyways, good grounds, good flasher, and a new gauge fixed mine. It still bounces a tiny bit but not bad.
  2. Madison Mehlhose

    XJ Steering Shaft Upgrade (88-94 Trucks) 95+instructions on page 31

    I just "completed" this mod. Sorry if this is a repeat comment, i didn't want to read thru 47 pages to see if someone had incompatibility like me. BEWARE - i got my steering shaft off a 1999 Jeep Cherokee. I was thinking the later the year the less rust - being in the Midwest and all. The...
  3. Madison Mehlhose

    700R4 downshifts from OD to D on highway

    Playingwithtbi Can you go into more detail on how to view these settings and change them if possible. I have the necessary cable and software that you have screen shots of above. My truck TCC goes in and out depending on the weather at about 75 on the highway and I’d like to adjust the settings...
  4. Madison Mehlhose

    88 truck, runs great with the map unplugged

    There are 5 ground wires that terminate near the coolant temp sensor on my 89 are all 5 there on yours?
  5. Madison Mehlhose

    The Stupid Lift Questions Thread

    I second this. I want to put a small body lift (maybe 3") and new gears into my truck. It just so happens that 315/70/17 and 3.73 gears balance each other and i wont have to mess with the speedo gear. :) What are the tire size limits of cranking the keys and what are the limits of a mild 3" body...
  6. Madison Mehlhose

    CEL triggers only while cruising

    Have you run into this problem or has someone else? I think the intake vacuum alone should be within the control window of the ECM to compensate for small changes in back-pressure.
  7. Madison Mehlhose

    CEL triggers only while cruising

    Mine was tucked into the wiring harness shield thingy and cut short with no connector or anything. I attached it to the intake manifold ground near the temp sensor.
  8. Madison Mehlhose

    CEL triggers only while cruising

    Is there something you would recommend? It’s true dual setup.
  9. Madison Mehlhose

    CEL triggers only while cruising

    SOLVED!!! Yup that did it. Oxygen sensor is reading great now. Only issue now is i'm getting some spark knock - but its probably just from fuel trims that are way out of wack. I hope the computer will work it out soon! Moral of the story: Get an exact service manual for your truck Check...
  10. Madison Mehlhose

    CEL triggers only while cruising

    https://imgur.com/pqiZgU4 https://imgur.com/zor7Pc8
  11. Madison Mehlhose

    CEL triggers only while cruising

    IMG_0691 (1) by Madison Mehlhose posted Aug 30, 2018 at 1:13 PMIMG_0690 (1) by Madison Mehlhose posted Aug 30, 2018 at 1:13 PM I bought the actual service manual for my truck. I think it has the information i need. Just a very small note that wasn't on the other images i was seeing online. I...
  12. Madison Mehlhose

    CEL triggers only while cruising

    I verified my voltage measurements with another DVM and its accurate. See attached images for resistance. I re-checked the procedure of jumping the O2 harness to ground and starting and reading the voltage the scan data shows, no surprise, ~0.45v. It shows 0.4 to 0.5v almost all the time. I...
  13. Madison Mehlhose

    CEL triggers only while cruising

    This is the third sensor I’ve put in there. Currently I think it is the Bosch 13077. The sensor seems to be reacting as it should. I did the test where I simulate a lean condition and a rich condition.
  14. Madison Mehlhose

    CEL triggers only while cruising

    Yes sir, i agree it should not be 1.5v, nor any voltage there at all. What do you think is happening?
Top