Recent content by HPIII

  1. HPIII

    Lunch Box Locker for my 10 bolt rear end?

    Sorry it took so long to reply. Mines still holding up with no issues. So far so good! Sent from my iPhone using Tapatalk
  2. HPIII

    Looking for Front end grill and bumper images

    Race Stars. 17x7 on the front & 15x10 on the back. Sent from my iPhone using Tapatalk
  3. HPIII

    Lunch Box Locker for my 10 bolt rear end?

    Installation was easy. Just need some new oil for the differential and some good sealant/rtv for the cover. Took a couple of hours on a Saturday morning.
  4. HPIII

    Lunch Box Locker for my 10 bolt rear end?

    I installed a powertrax in my stock 10 bolt (see attached picture). It has held up now for over 6 months. As stated above I’ve seen mixed reviews, I chose it simply because if I’m going to drop $1000+ dollars in the rear differential I want to get rid of the 10 bolt all together. I’ve got a...
  5. HPIII

    95 ls swap almost done but...

    I don’t remember exactly but I was slightly concerned with how much mine was engaged into the transmission. I have a 4/6 drop as well, don’t know how much that may have changed it either. I can measure mine this weekend. I’ve been beating on mine fairly hard with no issues for close to a year.
  6. HPIII

    95 ls swap almost done but...

    These are the u-joints I used as well as the yoke part number. I believe I ordered that yoke from Jegs. My truck is a 93 shortbed, early 90’s 4L80 dirty dingo adjustable mounts. Sounds like the same setup.
  7. HPIII

    Looking for Front end grill and bumper images

    Stock 1993 with clear/frosted corners.
  8. HPIII

    Post YOUR Favorite Picture of YOUR Truck!!!

  9. HPIII

    What is everyone doing for headers?

    I’m running Schoenfeld swap headers and they fit fine, no complaints at all so far. Don’t believe they will clear on 4wd without a suspension lift.
  10. HPIII

    Need wiring help with ls swap

    You are going to have to modify the stock 6.0 harness(or buy a stand-alone harness), lt1swap.com is your friend. There is a ton of information for the ecm pin out and wiring schematics. I don’t know exactly which wires go where.
  11. HPIII

    Need wiring help with ls swap

    What year 6.0? The voltage gauge should continue to work as you will retain supplying power at the firewall with the wire that also used to connect to the alternator. The oil pressure gauge and coolant temp will reuse the existing sensors/wiring you will just need adapters for the 6.0...
  12. HPIII

    1993 6.0 Swap

    I finally got around to getting my factory speedometer working. For anyone else who may need to know there is a light blue wire at the DRAC module behind the glove box that you can tie the signal from the LS ECM directly to to provide signal to the factory speedometer. I did have to change the...
  13. HPIII

    1993 6.0 Swap

  14. HPIII

    1993 6.0 Swap

    Well I went from the 4L60 to the 4L80 so I think the 3:73’s will help compensate for the gearing difference. I’m not dead set on 3:73’s but 3:42’s aren’t cutting it, plus I need a posi unit.
  15. HPIII

    1993 6.0 Swap

    I need to look into the sanden compressor/conversion. I completed a lq4 swap in a 1990 Z71 I had and used the Dirty Dingo bracket for the R4 compressor. The bracket was very nice but it resonated when the compressor was on and made a growling noise. Thanks for the tips on the air filter. The...
See more

Latest posts

Members online

Total: 1,453 (members: 42, guests: 1,411)

Forum statistics

Threads
64,255
Messages
1,389,919
Members
51,252
Latest member
Smittyrcsb

Share this page

Top