Recent content by GTPI

  1. GTPI

    Hydrostatic mower not moving?

    That lever disengages the hydro so it will freewheel, with the battery out your dad may have disengaged it so he could push it
  2. GTPI

    Windshield replacement woes

    LMC has all windshield in stock as of 3/21/23! Hope this helps someone.
  3. GTPI

    Should I Take a cab?

    The cab I found is very clean, rust free. I'm just concerned with which years are compatible .
  4. GTPI

    Should I Take a cab?

    I was at my local salvage yard today and found three standard cabs, all 90's but not sure of the exact year. They were all clean rust free and I got to thinking I should just swap my cab rather than repair rust. My truck is a 1988 so I'm not sure if any of the later cabs will work. The rust is...
  5. GTPI

    Wires just hanging

    @Schurkey Thanks, there was the typical plastic cover on the wire in the first photo and it did travel down through a large metal heat shield along with the starter wires. Where would a knock sensor typically be? I also found several wires at the terminal block on the left side of the...
  6. GTPI

    Wires just hanging

    So things are still in the clean up stage, hope to have her running soon. I found a few wires just hanging and I was hoping to find where they belong . First one tied around the trans lines near the starter , first photo. The 2nd photo shows three connectors found laying on the intake manifold...
  7. GTPI

    Door Hinge Pins & Bushings, Cunningham Machine vs. New Greaseable GM?

    Here are the clips, they can be purchased separately for $4.10 ea. They have a good selection of hinge parts . Hinge pin clips
  8. GTPI

    Strange Noise Where There Shouldn't Be One

    Do you still have the original sensor? If you do, try putting it back just to see if that eliminates the noise. Also check the new one for any unusual contact marks.
  9. GTPI

    Sway bar issue with DJM control arms

    It looks like DJM offers these articulating links to make it a little less painful ! Sway bar links . I'm sure there is a better way
  10. GTPI

    Do I Dually?

    Thanks for all the help, hopefully ill get to see it tomorrow.
  11. GTPI

    Do I Dually?

    I found this close enough to me that I want to go have a look. It's a 99 with 216 on the clock, don't know much about it yet. Asking price is $5500. Is this a decent price if it runs well and is structurally sound?
  12. GTPI

    Hello from SW Florida

    So would it wise to source a 350 tbi and if so do I need any of the electronics from the donor vehicle? Transmission is a 700r4 but I won't know it's condition until the truck is running. Thanks
  13. GTPI

    Hello from SW Florida

    Thanks for the welcome! I was looking at this 2000 K1500 and then I saw the 88 just waiting to be towed away. Someone else is going to get a really nice truck. The owner of this silver gem is asking almost 13K, I gave my neighbor $500. for the truck I just named the "Recycle Bin"
  14. GTPI

    Hello from SW Florida

    Hi everyone , Joined about a week ago and after a short time I knew this was the place to be! I was looking for a cool project and found this 88 w/Scottsdale trim sitting on the side of my neighbors house. I think it was his first vehicle and needless to say it didn't last long, it...
See more

Latest posts

Staff online

Members online

... and 27 more.
Total: 1,839 (members: 77, guests: 1,762)

Forum statistics

Threads
64,326
Messages
1,391,423
Members
51,430
Latest member
Noel11

Share this page

Top