Recent content by fastfreddys454ss

Wipers won’t shut off

Going back to my wiper problem. When my wipers are on all the time with the switch turned off and keys out of the ignition. After replacing 2 wiper motors with modules and 2 wiper switches. Has anyone had this problem before or know what else to look for.
- fastfreddys454ss
- Post #8
- May 2, 2021
- Forum: Audio + Electronics
Wipers won’t shut off

I wish it were as simple as a fuse. Unfortunately the fuse only goes in one way. I first disconnected just the white wire and it turns the wipers off. Then put it back in and they start running again. After that I disconnect the gray wire and it stops the wipers. Hook it back up and it also...
- fastfreddys454ss
- Post #4
- May 1, 2021
- Forum: Audio + Electronics
Wipers won’t shut off

I have a 1990 Chevy truck with intermittent wipes. My wipers run all the time even with the switch turned off and no keys in the ignition. Theres no park or intermittent control either. It run at low speed all time .The only thing I can do is go from low speed to high speed. Without the ignition...
- fastfreddys454ss
- Thread
- Apr 30, 2021
- Replies: 15
- Forum: Audio + Electronics
My 454 SS build

Got the profile prism halos in today. Got tired of seeing dim halos ,weird designs, and expensive prices. Don’t know what they were thinking with most of the halo headlight bucket designs for the OBS. So I built my own.
- fastfreddys454ss
- Post #118
- Apr 11, 2021
- Forum: Street Build Threads
My 454 SS build

Finished the dash repair today. Just have to wait and let it dry 24 hour. Then clean up all the bondo dust and put everything back together
- fastfreddys454ss
- Post #117
- Apr 11, 2021
- Forum: Street Build Threads
My 454 SS build

Installed some wamrods hood struts. I like them, but I just have to be careful I don’t bump my head on the hood. The hood doesn’t open up as high. I might move the bottom mounts back a little bit. If that doesn’t work I may order longer struts.
- fastfreddys454ss
- Post #116
- Apr 1, 2021
- Forum: Street Build Threads
My 454 SS build

Got the c type tail light in today.
- fastfreddys454ss
- Post #115
- Apr 1, 2021
- Forum: Street Build Threads
My 454 SS build

Trying J B Plasticweld putty to repair dash. So far so good. Next the fun part. Sanding and painting.
- fastfreddys454ss
- Post #114
- Apr 1, 2021
- Forum: Street Build Threads
Car stereo in dash pocket

Sorry wasn’t sure what kind of experience you have. I am definitely interested In what you come up with.
- fastfreddys454ss
- Post #24
- Apr 1, 2021
- Forum: Audio + Electronics
Car stereo in dash pocket

There’s no way with 1st, 3rd and 5th gear you will be able to get a center console if front of the shifter boot. Your best bet is a single din radio bezel. If you haven’t done one before. You don’t have to cut the dash out. You just have to reused your heater vents and bezel clips. You can order...
- fastfreddys454ss
- Post #22
- Apr 1, 2021
- Forum: Audio + Electronics
Car stereo in dash pocket

Next is dash repair. Made some plastic tabs and used some pvc cement to hold it in. I think I going to try some j b plasticweld putty or thicken up the pvc cement by leaving the cement can open so the acetone evaporates a bit. Then do a body work, sand it and paint it with some colorbond
- fastfreddys454ss
- Post #19
- Mar 30, 2021
- Forum: Audio + Electronics
Car stereo in dash pocket

I already posted this in street build, but wanted to finish this thread. I installed the retrosound M4 stereo, put in the rear view safety 5” monitor in the console with the a license plate reverse camera and clean up the center console
- fastfreddys454ss
- Post #18
- Mar 30, 2021
- Forum: Audio + Electronics
My 454 SS build

Next also going to remove my current led tail lights and install new c type leds. But haven’t decided if I will tint them with some VHT nite shade or not. I think I put them in first and then figure out what I will do after I see then on the truck.
- fastfreddys454ss
- Post #112
- Mar 29, 2021
- Forum: Street Build Threads
My 454 SS build

Next week I’m putting in new profile prism rgb fitted headlight halos from Led concepts with a little customization. Not a very good rendering, but you can get the idea of what I’m going to do. I will make a full write up next week on how to put them in after I’m done. The old spyder halo head...
- fastfreddys454ss
- Post #111
- Mar 29, 2021
- Forum: Street Build Threads
My 454 SS build

Next I partially glued in the part of the dash I cut out for the double din radio.with pvc cement. After it dries I will thicken up the pvc cement by leaving the glue bottle open so the acetone evaporators inside the can. Turning it to a paste to fill in the cracks.Then do a little body work...
- fastfreddys454ss
- Post #110
- Mar 29, 2021
- Forum: Street Build Threads