Recent content by delta_p

  1. delta_p

    Solid rear window to sliding window

    There is no gasket on my '96. Just High Viscosity Windshield Adhesive. The glass is already in a sealed frame. You just cut the old adhesive from inside the cab and pull the rear unit out, clean up, prime, add adhesive on the new unit frame, put it in and tape it in place to cure.
  2. delta_p

    96' L31 timing and crank relearn

    I have a '96 5.7l. on my Iphone, when i open dash command I can select account, purchase, GM (chevrolet, buick, etc.), and i can see there is extended parameters for '96 - 2009. I have a green check mark next to the '96 since it has been purchased.
  3. delta_p

    96' L31 timing and crank relearn

    In Dash Command you have to purchase the GM extended parameters. The parameter ID for Cam Retard (CKP / CMP Correlation) is GM.ENGINE.CR (°) found in the general PID's.
  4. delta_p

    How to stop LED Fast Flash info

    I used 6 ohm/50 W resistors because that was about the equivalent resistance of the 1157 bulb or whatever bulb was used given its wattage ect. Not sure what actually could be used, I just stuck with that. Just make sure to put them across the turn signals so they are only powered during the...
  5. delta_p

    How to stop LED Fast Flash info

    That's how I did mine and everything works fine.
  6. delta_p

    How to stop LED Fast Flash info

    Probably is a resistance issue. The marker lamps finds grounds through the resistance paths of the unlit park lamps in normal operation ect. of turn signal and hazards. Since the park/turn lamps are now LEDs they don't have the same resistance like the bulbs did since they are diodes. So the...
  7. delta_p

    molding removal and adhesive cleanup

    I used a heat gun and piece of fuel hose to scrape and ball up the adhesive. Like your fingernail but saved my hands from all the pushing. The hose was soft enough and didn’t take paint with it.
  8. delta_p

    Brake bleed question

    What i have been doing is using a cheap ebay adjustable DC-DC buck converter in a home built interface between the cig lighter and the tech2 to hold the voltage to 12V (above 9v) on the input pin of the DC-DC converter (Mornsun) inside the unit. I put the digital voltage display on it. (Edit...
  9. delta_p

    Brake bleed question

  10. delta_p

    Brake bleed question

    Yeah my tech 2 is a clone and it came with all the connections. As far as I can tell, the clone is just an unbranded version of the original. It hasn’t limited me on anything described in its use in the GM service manuals. I did make an interface using a voltage regulator from the cig lighter...
  11. delta_p

    Brake bleed question

    There is an OBD1 12 pin adapter came with the tech2 for DLC cable but the tech 2 has to be externally powered. Will it not communicate through the connector? Here is a vetronix manual (pdf) https://www.obd2be.com/download/gm-tech-2-user-manual.pdf
  12. delta_p

    Brake bleed question

    Never worked with the 95. But I cycled through my tech2 for a 95, and it still shows a function test for each option 4 WAL 3 Sensor or RWAL. I assume it is the same test? but again I have never done it. Only my '96.
  13. delta_p

    Brake bleed question

    I have used my tech2 to cycle the ABS pump and valves on my '96 C1500. This is just a function test though, that's why you run it several times. Chassis>4WAL 3 Sensor>Special Functions>Function Test On a '98 it looks like there are more option than just running function test, Automated Bleed...
  14. delta_p

    Seeking small air compressor recommendations

    I bought small compressor at HF with 8 gallon tank with the wheels on it to roll it back out of the way in the garage. I also bought an 11 gallon receiver tank that I can hook up in parallel when needed for the volume. I got family spread out in town and this makes it easy for me to transport...
  15. delta_p

    Seat foam

    Anyone think the Auto-champ-texas drivers cushion linked above will fit in the place of the passenger side of the 60/40 split bench in a '96? I don't see a passenger side in searching.
See more

Latest posts

Members online

... and 14 more.
Total: 1,436 (members: 64, guests: 1,372)

Forum statistics

Threads
64,247
Messages
1,389,801
Members
51,236
Latest member
Old97silver

Share this page

Top