Recent content by Colorado2500

  1. Colorado2500

    TBI 350 jumpy timing

    Update: Ordered a new Davis Unified Ignition distributor, I'll update when I get it installed.
  2. Colorado2500

    TBI 350 jumpy timing

    I was around it enough, it didn't move, but I should triple check it. Thanks for the input though, maybe someone will read this in the future and have an Ah-Ha! moment!
  3. Colorado2500

    C1500 Disc Brake Recommendations

    Stock solid rotors and high quality pads (like from EBC, Stoptech, Hawk, Wilwood) are the way to go. I have some carquest ceramics and they are good enough I can't justify upgrading. What you picked out looks good, however, These might work better and are cheaper...
  4. Colorado2500

    TBI 350 jumpy timing

    True, I was just watching one a few mins ago actually. Doesn't look too bad at all. Sent from my LG-H820 using Tapatalk
  5. Colorado2500

    TBI 350 jumpy timing

    Did some more testing. This time with the timing wire still connected, idle the timing was all over from 16 degrees to 20 degrees. I heard the ecm controls that at idle and some moving around is normal. However I then revved it to about 2000 rpm and watched the timing hold steady but then...
  6. Colorado2500

    TBI 350 jumpy timing

    Truck has had a rough idle for a while now, but other than that, it ran well. Recently, it begin to idle so poorly that it would barely run and would stall. Diagnosed as a bad EGR valve, valve was stuck open with bits of something. Replaced EGR valve & solenoid as well for peace of mind. After...
  7. Colorado2500

    Pre-Bent or OEM replacement brake lines?

    Okay great mine's a C2500 w/ the 9.5 so it should be fine. Thanks again, don't know why I couldn't find these a week ago.
  8. Colorado2500

    Pre-Bent or OEM replacement brake lines?

    Nice man. Is the truck you put them on a 6 lug or an 8 lug?
  9. Colorado2500

    Pre-Bent or OEM replacement brake lines?

    Where did you find them? I'd like the factory look on my axle again. Sorry to sidetrack your thread OP.
  10. Colorado2500

    Colorado2500's 1989 C2500 ECLB Build (The Little Big Truck)

    Yeah just wondering, I'll look around some more. Thanks man.
  11. Colorado2500

    Colorado2500's 1989 C2500 ECLB Build (The Little Big Truck)

    Lost my grille emblem when I got stuck, anyone know where I can get one for cheap? Would one off a GMT800 or GMT900 fit?
  12. Colorado2500

    Colorado2500's 1989 C2500 ECLB Build (The Little Big Truck)

    Yeah it's a good truck, but not for what I need. I'm not sure yet what I'll get, a lot depends on how much I get for my truck. I'm thinking about a smaller SUV of some kind with good stock capabilities, aftermarket support, and preferably a manual trans. Ideally a K5 Blazer or a Jeep wrangler...
  13. Colorado2500

    Colorado2500's 1989 C2500 ECLB Build (The Little Big Truck)

    Well it's been a while since an update, but the truck has been fine besides being the absolute worst winter vehicle. And then this happened: Slid down this snowy trail sideways while out sledding with my roommates, completely high-centered it. It was out there for 2 days, we tried digging it...
  14. Colorado2500

    Colorado2500's 1989 C2500 ECLB Build (The Little Big Truck)

    Well I hope that won't happen! I like the Energy parts a lot too, it's quality and handling is much better. Definitely the way to go when replacing stuff.
  15. Colorado2500

    Colorado2500's 1989 C2500 ECLB Build (The Little Big Truck)

    I just used the Energy Suspension kit for my truck, I didn't see any size options for mine.
See more

Latest posts

Members online

Total: 1,579 (members: 49, guests: 1,530)

Forum statistics

Threads
64,247
Messages
1,389,737
Members
51,235
Latest member
ggddff

Share this page

Top