Recent content by Cole Chambers

Throttle Body Modifications

What does the relearn do?
- Cole Chambers
- Post #15
- Apr 25, 2019
- Forum: Engine Performance + Maintenance
Throttle Body Modifications

The torx was turned all the way in before I did the mod so i couldn't turn it anymore. And no, the idle is still the same as it has always been.
- Cole Chambers
- Post #14
- Apr 25, 2019
- Forum: Engine Performance + Maintenance
Throttle Body Modifications

Here is what I meant by the whole zip tie deal.
- Cole Chambers
- Post #10
- Apr 24, 2019
- Forum: Engine Performance + Maintenance
Throttle Body Modifications

So basically, when my tb plate closed all the way the pedal became almost as some called it an "On-off switch". While playing with the butterfly I noticed there was a small torx where the top of the butterfly rested, so in order to remove the stiff stop in the pedal, i but a zip tie around the...
- Cole Chambers
- Post #8
- Apr 24, 2019
- Forum: Engine Performance + Maintenance
Throttle Body Modifications

I'll try to get you a picture later on around 3:30
- Cole Chambers
- Post #7
- Apr 24, 2019
- Forum: Engine Performance + Maintenance
Throttle Body Modifications

I decided to take a risk today and cut the "flap" off of my throttle body blade. After getting everything back together, I noticed that the gas pedal was extremely stiff and almost made it impossible to drive. However, there was a great amount of improved acceleration (NOT HORSEPOWER). Upon...
- Cole Chambers
- Thread
- Apr 23, 2019
- Replies: 19
- Forum: Engine Performance + Maintenance
The Body Lift Thread

How did you bring the step bars up with the body lift?
- Cole Chambers
- Post #826
- Mar 3, 2019
- Forum: Stock Suspension + Bolt On Kits
The Body Lift Thread

I'd been searching for another truck with that sort of lift and 315's but never found one. Your truck looks sick man.
- Cole Chambers
- Post #824
- Jan 16, 2019
- Forum: Stock Suspension + Bolt On Kits
The Body Lift Thread

Just in case anyone was wondering.. It is possible to fit 315/75r16 on 16x10 wheels if you have a 3 inch body lift and adjust the torsion bars a little. I have a two inch block in the rear and have the torsion bars up 3/4 of the way. I had to trim the lower plastic valance of the bumper at an...
- Cole Chambers
- Post #820
- Dec 12, 2018
- Forum: Stock Suspension + Bolt On Kits
The Body Lift Thread

Thats what ive seen. I don't know if this issue would be a big one. I have a vortec.. but i'm pretty sure that's why they say they won't fit the diesels. But they also might, i'm sure the is someone that has but a body lift on a diesel model.
- Cole Chambers
- Post #819
- Dec 4, 2018
- Forum: Stock Suspension + Bolt On Kits
Torsion Bar crank

So how bad is your ride? And also, have you had any issues with the front end parts wearing out?
- Cole Chambers
- Post #14
- Nov 28, 2018
- Forum: Stock Suspension + Bolt On Kits
Not the normal brake light issues.

I’m having a problem with my 97 K1500. I had a tailgate brake light strip that suddenly started displaying the incorrect sequence of lights. When I press the brake the third brake light lights up like fine, but the actual tail lights light up the wrong bulbs. My rear turn signal lights up when...
- Cole Chambers
- Post #13
- Oct 23, 2018
- Forum: Audio + Electronics
The Body Lift Thread

How much did you have to cut from the back of the fender?
- Cole Chambers
- Post #816
- Oct 11, 2018
- Forum: Stock Suspension + Bolt On Kits
The Body Lift Thread

3 inch body lift and 285/75r16
- Cole Chambers
- Post #815
- Oct 10, 2018
- Forum: Stock Suspension + Bolt On Kits
LED Gauge Install

How hard was it to remove the dash to get to the bulbs?
- Cole Chambers
- Post #912
- Oct 3, 2018
- Forum: OEM and Custom Interiors