Recent content by c1500deathtrap

  1. C

    part out, 91 c1500

    Located in Hampton VA
  2. C

    part out, 91 c1500

    Parting out my 91 C1500. It has a TCI streetfighter 700r4, built SBC bored .030 over, flat top pistons, with aluminum heads a cam edelbrock torker2 intake, edelbrock 4bbl tbi injection system, and long tube ceramic headers. 10 bolt 3.43 rear end, american racing torque thrust 2's 17x8 wheels. No...
  3. C

    ****** v-band clamp install

    As for the welded clamp, careful work with a cutoff can save it, or beat it off and buy a new clamp.
  4. C

    ****** v-band clamp install

    Its normal to hang one pipe slightly out of the v-band clamp. As long as the other half has its pipe recessed. It helps align the clamps and improves sealing. They make interlocking v-bands that have a lip and corresponding groove, but that is a cheap effective way of doing it.
  5. C

    TBI on a dual plane Manifold??

    I thought it was higher rise=longer runners=better low end torque.....
  6. C

    High mileage motor thicker oil?

    It was introduced in ww2 for use in airplane engines, but ok.
  7. C

    Trouble installing harmonic balancer - it gets to the same spot and then binds

    You may have accidently gotten an undersized balancer intended for crank snouts that have been turned down. Measure the id of the snout and see if it is in spec. otherwise take the timing cover off and polish up the snout with some emery cloth. surface finish shouldn't be to important here, so...
  8. C

    91 rclb

    1/2 ton 2wd 1991 gmc Long bed regular cab for sale. located in Hampton Roads VA. TCI 700r4 transmission, 350 small block with aftermarket fuel injection, shorty headers, vortec haeds and a lunati camshaft. aluminum wheels ( american racing torque thrust 2's). Message for pictures. engine and...
  9. C

    Hard hot start - temp sending unit, how to diagnose?

    Read by checking resistance across the two prongs on the sensor. Try a hot start with your foot to the floor (the flood clearing mode described earlier) could have an injector leaking down when the manifold gets heat soaked after shut down. My geuss is it's fuel related.
  10. C

    Camshaft 350 v8 5.7 - 1988 k1500 Scottdale

    an icm can be tested by most parts stores just bring it in.
  11. C

    Cylinder heads

    If it was me i would save my money and buy a nice set of heads that will run a vortec manifold.
  12. C

    Cylinder heads

    https://www.thirdgen.org/forums/fabrication/588127-lt1-head-conversion-project-2.html Look what i found!
  13. C

    Cylinder heads

    So you would have to use an lt1 or 4 manifold (no distributor) or a gmpp 24502592. The coolant flow is reversed, not a big deal, but there is no tstat in the intake, and the coolant passages in the deck are different (steam vents i believe). So, mount the heads, make a coolant manifold to house...
  14. C

    Camshaft 350 v8 5.7 - 1988 k1500 Scottdale

    Why not check the tappet lift before tearing apart the top end? Unbolt a rocker arm, and measure the travel of the pushrod as you turn the motor over by hand (or power if you like). Across a standard 1.5 rocker the tappet lift should be a quarter inch or so. Dial indicators are preferred, but a...
  15. C

    How does it work?

    just a generic vacuum referenced fpr, Should help you get an idea for it. Theres quite a few different versions, in most cases vacuum pulls back a spring opening a bypass to return fuel to the tank or pump inlet. Reduced vacuum (more throttle opening or load) closes off the bypass port...
Top