Recent content by BulldogSS

  1. B

    72 c10 350 build

    Rpm range- right now it idles around 650. After heads and cam I’m assuming it may a little more. Factory converter is somewhere between 1400-1700 I’m reading. So maybe 1500-5500???
  2. B

    72 c10 350 build

    Erik thanks for the reply. It’s funny I’m narrowing down parts and both the cam and intake you posted are top choices. My cam will be flat tappet though. I’ve seen lots of people using the next size up 268 cam but with my stock converter and tall gears I’m thinking I’ll get more useable power...
  3. B

    72 c10 350 build

    Erik just out of curiosity what cam did lunati spec for you? If your set up is anywhere near similar to mine
  4. B

    72 c10 350 build

    Pic of the truck. Just because
  5. B

    72 c10 350 build

  6. B

    72 c10 350 build

    The rear end will have to stay 3.08 unless at some point I swap to a 700r4. I’ve considered adding a trutrac but feel it’s not worth opening the rear end until I’m ready to do gears and full rebuild. I’ve been looking quite a bit at the comp xe268 and the lunati voodoo equivalent. I think either...
  7. B

    72 c10 350 build

    If this post is in the wrong section pleas move where deemed appropriate. I totally agree a rear end upgrade would be huge for fun factor however the truck does see some highway use and with the th400 and the 3.08s I’m turning 3000-3100 at 70mph. With 3.73 I’d be running 3700 or so. What’s the...
  8. B

    72 c10 350 build

    I’m putting together a 350 for my c10. Im going to lay out what the truck currently has and also what I’d like to do to the motor. I’d like to get some criticism and/or advise. End goal is to have a dependable motor with tons of torque. The truck is not my daily but I’d like for it to be built...
  9. B

    Going to get EBL!! What cam and intake?

    Prob a good idea to learn the EBL set up on the stock motor. there’s a 3704 on marketplace for $200 near me. Although I’ve read that there are better options.
  10. B

    Going to get EBL!! What cam and intake?

    So I’m using my stimulus money to stimulate the truck. Going to just jump both feet in and order the EBL set up. I’m looking for some advise on a cam and intake set up that a novice like me would have a decent shot at getting dialed in. I’m sure there are options that a experienced tuner could...
  11. B

    Cracked manifold. Go shorties or afterburner

    Yeah I had a set of ceramic pacesetter Lts on my 2003 Silverado ss. My brother has the truck now and they still look good after about 12 years. Just showing a little rust down at the collector.
  12. B

    Cracked manifold. Go shorties or afterburner

    Thanks for that but I already ordered the shorties they actually were delivered Friday. The only reason I’m am doing the swap is because one of my stock manifolds is cracked. So might as well get rid of the stock y pipe as well. I found the flowtech shorties for $99 and matching y pipe for $90...
  13. B

    Cracked manifold. Go shorties or afterburner

    I went ahead and ordered the flowtech ceramic shorties with matching y pipe. They were $290 total shipped from Holleys eBay store. I’ll try and do a before and after sound clip for anyone that may be interested. I’ll also post up how smoothly( or not) they bolt up. Also on that eBay store they...
  14. B

    Cracked manifold. Go shorties or afterburner

    Thanks for all the replies.
  15. B

    Cracked manifold. Go shorties or afterburner

    Truck is a 94. Currently has cracked stock manifold to stock y with cat removed(the original was rattling) then 3in pipe into a borla. Just found ceramic coated flowtech shorties on holleys eBay for $199 matching y pipe for $90. I’m going to order those and give them a try.
See more

Latest posts

Members online

... and 1 more.
Total: 1,506 (members: 51, guests: 1,455)

Forum statistics

Threads
64,336
Messages
1,391,511
Members
51,441
Latest member
omcvay

Share this page

Top