Recent content by ArdentFab

  1. ArdentFab

    Ardent Fabrication Autocross Truck

    Been a while, lots of changes but will post more pictures later. Some from LS Fest Texas 2022 at Texas Motor Speedway.
  2. ArdentFab

    Ardent Fabrication Autocross Truck

    Hahaha never heard that before but I like it! That also means I just gotta figure out which ones are wrong :Big Laugh:
  3. ArdentFab

    Ardent Fabrication Autocross Truck

    Been a while since I've been here but here's an update! --- Ardent Fabrication's Autocross OBS Truck Three-link with a Panhard Bar! . This rear suspension set-up will allow me to tune in some anti-squat and roll-steer to really get some grip off the line and around the corners where it counts...
  4. ArdentFab

    Ardent Fabrication Autocross Truck

    I used a pre-'95 clutch pedal assembly, typically found in the V6 worktrucks or other RCSB. I think I moved the transmission crossmember forward like 2"-3", can't recall exactly ATM. Just scoot it forward and drill new holes. I even reused the polyurethane transmission mount that I had on the...
  5. ArdentFab

    Ardent Fabrication Autocross Truck

    Yea, I got mine from LKQ for $315 with like a 3 month/3,000 mile replacement warranty. Can't complain about that! You could find them cheaper through private sellers on Craigslist or Facebook market place. Sent from my SM-N960U using Tapatalk
  6. ArdentFab

    Ardent Fabrication Autocross Truck

    Availability and cost. I've read from multiple sources theyre good for about 500HP and I havent had any issues with mine and really like it. It's a good alternative to T56. I'm in it less than half the typical cost of a used T56 that needs a rebuild. Much appreciated man, with the right parts...
  7. ArdentFab

    Ardent Fabrication Autocross Truck

    I don't have like a super detailed writeup really but I can explain kind of what l did and used essentially. Supercharged111, you're right, I did use a 4L60E bell housing but it had to be a particular one with a 7" depth, GM #24206952. Mine came from my buddies 2002 Silverado. As for the...
  8. ArdentFab

    Ardent Fabrication Autocross Truck

    Yes, correct, I welded the brackets on [emoji106] Sent from my SM-N960U using Tapatalk
  9. ArdentFab

    Ardent Fabrication Autocross Truck

    Much appreciated! Looking forward to seeing yours [emoji109] Sent from my SM-N960U using Tapatalk
  10. ArdentFab

    Ardent Fabrication Autocross Truck

    It's been a while and I haven't been updating this build thread but here it is! A lot has been going on but I recently competed in the Protouring Truck Shootout in Kentucky and placed 2nd in my class! Here are the specs as of August 25, 2020: Powertrain: - LH6 5.3L aluminum engine - SDPC LS6...
  11. ArdentFab

    Oil Catch Can/Windshield Washer Tank Combo

    Well actually, since I'm better than starting an argument with someone online, I won't continue this conversation. I'll be the bigger person and stop right here before I waste anymore of my valuable time. I actually have better things to do than this. - As for everyone else, I really...
  12. ArdentFab

    Oil Catch Can/Windshield Washer Tank Combo

    I was thinking about that too; a windshield washer tank combo was just easier to make without disabling the truck at that time I was making it since it was my daily driver haha
  13. ArdentFab

    Oil Catch Can/Windshield Washer Tank Combo

    Yes, because that's obviously how they work...
  14. ArdentFab

    Oil Catch Can/Windshield Washer Tank Combo

    Thank you for your input Schurkey, but the question was "did it work", not "what is your opinion". Being that I made it, I figured I'd be the one to answer the question. So to answer the question, it did work. Collected a lot of water and oil but my engine has wear in the cylinders and/or worn...
  15. ArdentFab

    Bucket Seats, Adjustable Brackets, and Harness Bar - Ardent Fabrication

    It's as far back it can really go. Otherwise you won't be able to put that rear panel on. Sent from my SM-N960U using Tapatalk
Top