-
-
I really appreciate you taking the time to explain and sharing in what you've figured out along the way. Nice ride, by the way! I'm... -
The_Family_Tahoe reacted to KansasOBS's post in the thread Really wish ppl would stop bringing me trucks with hydraulic fluid in trans with
Like.
Well, what I was trying to touch base on, and partially mentioned in this thread earlier. Is heaver oils are harder to push, also... -
The_Family_Tahoe replied to the thread 90 truck with 86-87 Corvette engine.I completely agree the aftermarket EFI manufacturers are not being honest. Dyno tests have shown repeatedly the longer runners will make...
-
The_Family_Tahoe replied to the thread 1996 Tahoe 4/6 Drop kits.Thank you! Yes, I put the cluster in it. At the risk of hijacking this thread I will share I need to remove the cluster and repair the...
-
The_Family_Tahoe replied to the thread 1996 Tahoe 4/6 Drop kits.Those are the ones I used. 3/4" narrower works with my wheels which have 5.25" backspace and 8.5 inch wide. If your wheels stick out...
-
The_Family_Tahoe replied to the thread 454 swap? What does it entail?.The 454 will drive much better in a full size truck used for truck stuff in any comparison with a 6.0. Stock vs stock the 454 is easier...
-
Those are not stock shackles. However, if you just remove the bolt and position the leaf spring eye three holes down, it should be about...
-
The_Family_Tahoe replied to the thread 454 swap? What does it entail?.Just want to add the LS does a lot of things better than a big block. Power potential is not one of those things.
-
The_Family_Tahoe replied to the thread 1996 Tahoe 4/6 Drop kits.Use a control arm kit for the front. It is CRITICAL to narrow the front track width on these trucks if you are going lower. Stock width...
-
-
The_Family_Tahoe replied to the thread Interior paint.Yes. This is the paint. I searched my history and don't have any photos of the painted panels, but I'll get one and post it. I'll find a...
-
-
The_Family_Tahoe reacted to portmod7's post in the thread Long bed to short bed conversion with pics with Like.
This is similar to how I decided to do mine as well. Now you have me wishing I would have looked at doing it where the front clip is...
-
The_Family_Tahoe reacted to j 1985 chevy's post in the thread Long bed to short bed conversion with pics with Like.
Don't just dont I've done it on a 1993 or 4 k1500 but I did not do it like every one else to dow it right cab needs to come off
-
The_Family_Tahoe replied to the thread 1999 tahoe 4 door lowering question.Thank you. Mine is 2wd. There are 4wd lowering kits available. Belltech makes torsion bar keys to lower the front of a 4wd 1-3 inches...
-
-
Loading…
-
Loading…
Latest posts
-
-
Turn signal/Hazard Issue. Help greatly appreciated!
- Latest: Nad_Yvalhosert
-
Staff online
-
kennythewelderOfficially Retired, B31-3 (6-G) certified welder.
Members online
- Supercharged111
- Tonyz28
- Dan94
- crusty
- Girty
- 50TBRD
- 0xDEADBEEF
- Knutson
- Tommyblazer88
- Dachechinwolf
- Srg1016
- AlexG87
- MrSlick92
- SEVEN90_PARTS
- matt87
- Keeper
- snapshot
- Freelander
- Burbski
- Trio
- Cokeman95
- 95Noobie
- 89chevy4scrap
- Dud1f3r
- PolarBear
- movietvet
- SierraK2500
- Cv100902
- madboy101010
- rotorjockey
- Caman96
- Jerryred94silvy
- selland74
- RacerM95
- Michailcbd
- Pepsikid628
- Nad_Yvalhosert
- wnd lop
- kennythewelder
- 1996bluegreychevy
- Steve Cunningham
- Prospaceman
- BlueBurban
- TonyM
- Bob2650
- Drunkcanuk
- Jspr
- Cunhaleighton1991
- 1998_K1500_Sub
- slowfivespeed