Hipster
Latest activity Postings About
-
-
Hipster reacted to Sean Buick 76's post in the thread Rust Repair and overall restoration with
Like.
My best advice is to spend a good amount of time assessing each aspect of the truck to decide if it’s better to do one of the following... -
I've always subscribed to two criteria when choosing fuel, and it's a balancing act: 1. Go for very busy stations to guarantee fresh...
-
Hipster reacted to scott2093's post in the thread 1993 Yukon crate motor hydraulic roller lifter cleaning and adjustment journey - (Solved) with Like.
I really don't know.... It's a truck I bought 10 15..ouch ...years ago from a friend. A few years prior he had the motor replaced with a...
-
Hipster replied to the thread Rust Repair and overall restoration.I've used it. Phosphoric acid based but you can use Kleen-Strip prep and etch from the hardware store with a less fancy price tag, also...
-
Hipster replied to the thread 1993 Yukon crate motor hydraulic roller lifter cleaning and adjustment journey - (Solved).You sure this engine was mechanically healthy before you started with the lifter cleaning? As has been said about the lifters, sometimes...
-
Did not see in replies, but anybody else using Rust Mort after cleaning?
-
I'll add in that if you buy aftermarket replacement panels, I've been using Raybuck Auto Parts patch panels for my truck and I'm...
-
Hipster reacted to Canadian Rust Bucket's post in the thread Rust Repair and overall restoration with Like.
Good job keeping the old truck alive! Here's my $.02 on rust repairs, hope it helps. #1 top of the importance checklist is the frame. If...
-
Hey guys. This is a bit of a broad question, but I’m looking for some advice. I am the second owner of my 97 extended cab 4x4. Had it...
-
Hipster replied to the thread Engines 101.Has to be 30 years old, no safety, no emissions
-
:popcorn: Yesterday, I knew while driving to someone's house that I lost my brake lights, on my girls 1990 K2500. I had pulled over to...
-
Hipster reacted to tayto's post in the thread 1993 Yukon crate motor hydraulic roller lifter cleaning and adjustment journey - (Solved) with Like.
seems like way to much preload...i remember doing this on my caprice almost 20 years ago shop manual says 1.5 turns after zero lash. it...
-
Hipster replied to the thread 1993 Yukon crate motor hydraulic roller lifter cleaning and adjustment journey - (Solved).I've seen lifters squirt, but it's quirt , squirt, squirt. Never a constant stream just rolling out of them, inconsistent from one to...
-
Hipster reacted to tayto's post in the thread 1993 Yukon crate motor hydraulic roller lifter cleaning and adjustment journey - (Solved) with Like.
ya ive never seen them shoot a stream out like that. usually just a dribble and then the tip of the rocker fills up and pours off
-
Hipster reacted to Scooterwrench's post in the thread 1993 Yukon crate motor hydraulic roller lifter cleaning and adjustment journey - (Solved) with Like.
The oil should squirt out of those holes every time the lifter rises but not steady flow like yours are doing. How well did you clean...
-
-
Loading…
-
Loading…
Members online
- gbw83
- John Moore
- heskahoka
- 99xcss4
- JPVortex
- Sean Buick 76
- G1kon1wheel
- FNolen13
- Johan
- caw_86
- ralph93
- scott2093
- Supercharged111
- Road Trip
- jinks67
- 90sprobs
- SNCTMPL
- 1990 305
- skylark
- Zarko
- w300i
- Protegenoob17
- BonestockK1500
- someotherguy
- Chevyguy1282
- Mjourdain
- Rickyjason68
- Rock Hard Concrete
- dubglock23
- Drunkcanuk
- EricNeutel
- zopples
- 97Batmobile
- SuperSpore