Gmt400 brakes-master cylinder upgrade, residual valves, disc/drum MC differences. So much confusion.

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Ryan cin

Newbie
Joined
Nov 24, 2020
Messages
40
Reaction score
41
Location
Ny
I've been researching this all day. From what I've read:

- The low-drag calipers, which came on all 1/2 GMT400's, require a QTU (quick take up) master cylinder.
- The QTU master works by using a large piston to send fluid to the calipers fast, then a smaller piston to build pressure
- GM realized the mistake of using low-drag calipers, so they are not used on any other generation of trucks, including GMT800
- Rear drums seem to not require the 10lb residual valve
- The leading/trailing rear drums are ****, and there's no easy way to upgrade them

So,

IF all k1500 trucks use low-drag calipers, that require a QTU master, and there were no low-drag calipers or QTU masters after 2000, is the whole master cylinder "upgrade" bullshit? Using a GMT800 master seems like it could be causing most of my problems:

- It's a disc/disc master
- It does not have a QTU feature
- Front brake pressure builds late (explained below), which could be why my drums are slow to engage and seem to barely work

The lack of the QTU feature could be the reason for the long pedal travel before my pedal firms up close to the floor; the small piston has to send enough fluid to the calipers before they start to grab the rotor because of the low-drag feature. The larger piston on QTU-equipped masters sends this fluid in a much shorter pedal stroke, so the GMT400 brake pedal initial "mush" is the QTU feature in action, sending fluid to the low-drag calipers. This mush is much longer with the GMT800 master, because of the smaller piston moving less fluid.

Is there any merit to anything I just wrote? This is just my interpretation of all of the conflicting info I've read. Makes sense to me, but I have no clue what I'm talking about, and very well may be missing something. I do find it hard to believe that everyone that does this master cylinder "upgrade" has the same issues as me and ignores them simply because their pedal feels better.
 

Pinger

I'm Awesome
Joined
Mar 10, 2020
Messages
3,013
Reaction score
5,934
Location
Scotland.
At the wheel end, the force pushing either the pad or shoe is dependent (for any given line pressure) on the area of the piston. The area of a calliper piston and a cylinder piston vary quite a bit. (Remember area of a circle increases with the square of the radius - doubling the diameter quadruples the area).

Admittedly a disc set-up requires more force as it has very little self servo effect (especially when the pads are worn) compared to a drum set-up but it takes a leap of faith to imagine those factors exactly compensate for the widely different forces available due to wildly different piston diameter/areas.
 

phantom 309

OBS Enthusiast
Joined
Jan 17, 2018
Messages
57
Reaction score
36
Location
?
my 99 suburban had terrible squishy brakes,
i did all i could,. finally i deleted the KH abs,.
whole different truck
 

Schurkey

Supporting Member
Supporting Member
Joined
Jan 14, 2018
Messages
10,963
Reaction score
13,741
Location
The Seasonally Frozen Wastelands
So does this completely debunk everything about the praised “NBS Master” upgrade? To me, it sounds like there’s no suitable master cylinder except for the one made for these trucks... ...Thinking I’m going to try a new OEM master that’s actually designed for my truck.
Yes. Good plan.

So I do have the ****** drums. Any way to fix the issue of them getting thrown out of adjustment?
Use the park brake a lot. The rear drums adjust when you use and release the service brake, after using and releasing the park brake.

This is just plain negligent design. Folks go YEARS without using the park brake, especially on automatic-transmission vehicles.

I've been researching this all day. From what I've read...

- The low-drag calipers, which came on all 1/2 GMT400's, require a QTU (quick take up) master cylinder.
- The QTU master works by using a large piston to send fluid to the calipers fast, then a smaller piston to build pressure
Yes.

- GM realized the mistake of using low-drag calipers, so they are not used on any other generation of trucks, including GMT800
I don't know about that. Wouldn't surprise me that they were used on some Squarebodies, in the same way that the '87 Squarebodies had the same engine/transmission as the '88 GMT400s.

So far as I know, no GMT800s or newer trucks got the step-bore master cylinder. Perhaps there's some different design of low-drag caliper on them.

- Rear drums seem to not require the 10lb residual valve
Yup. Likely wouldn't hurt, but shouldn't be "needed".

- The leading/trailing rear drums are ****, and there's no easy way to upgrade them
Upgrade rear axle to a light-duty 3/4 ton, get a stronger axle and upgraded brakes as a bonus. I did. Be sure to match the gear ratio, and use a 4x4 donor axle in a 4x4 truck, a 2wd donor axle in a 2wd truck.


IF all k1500 trucks use low-drag calipers, that require a QTU master, and there were no low-drag calipers or QTU masters after 2000, is the whole master cylinder "upgrade" bullshit?
Folks have a defective QTU master cylinder, they "upgrade" to a fully-functional non-QTU master from a newer vehicle, and the brakes improve. IT'S MAGIC! I DISCOVERED A MAGIC UPGRADE!. 'Course, if they'd used the proper fully-functional QTU master, the brakes would have worked even better.

Using a GMT800 master seems like it could be causing most of my problems:

- It's a disc/disc master
- It does not have a QTU feature
Disc/disc isn't a problem...if there's no residual pressure valve designed into the disc/drum brake master cylinder. That was the only difference between a disc and a drum master cylinder aside from a potential bore-size difference...and GM quit using residual pressure valves in 1970.

Lack of the QTU feature IS a problem.

HOWEVER, I still suspect you've got air in the system, and maybe it's hiding in the rear ABS, maybe it's hiding in the master cylinder, maybe it's somewhere else. Somewhat common for air to leak INTO the drum wheel cylinders. I've also heard of folks buying aftermarket proportioning valves or Combination valves, and having air leak into the system via defective seals, without having fluid leak out.

Is there any merit to anything I just wrote? This is just my interpretation of all of the conflicting info I've read. Makes sense to me, but I have no clue what I'm talking about, and very well may be missing something. I do find it hard to believe that everyone that does this master cylinder "upgrade" has the same issues as me and ignores them simply because their pedal feels better.
I think you've largely got the right idea.
 
Last edited:

Pinger

I'm Awesome
Joined
Mar 10, 2020
Messages
3,013
Reaction score
5,934
Location
Scotland.
Upgrade rear axle to a light-duty 3/4 ton, get a stronger axle and upgraded brakes as a bonus. I did. Be sure to match the gear ratio, and use a 4x4 donor axle in a 4x4 truck, a 2wd donor axle in a 2wd truck.

.

Is that because they have different track widths?
 

Gibson

I'm Awesome
Joined
Aug 15, 2018
Messages
179
Reaction score
174
Location
oregon
The lack of the QTU feature could be the reason for the long pedal travel before my pedal firms up close to the floor; the small piston has to send enough fluid to the calipers before they start to grab the rotor because of the low-drag feature. The larger piston on QTU-equipped masters sends this fluid in a much shorter pedal stroke, so the GMT400 brake pedal initial "mush" is the QTU feature in action, sending fluid to the low-drag calipers. This mush is much longer with the GMT800 master, because of the smaller piston moving less fluid.
OK, even with "low drag" calipers the amount of fluid to squeeze them against the rotors is very small.
What you feel as "mush" is the much larger amount of fluid that has to be sent to the rear wheel cylinders.
The rears take a lot of fluid to move, and when the shoes do finally get to the drums they also shift and distort a little.
That is why the drums must be almost perfectly adjusted, with no worn parts to be "quick and firm", so to speak.
One of the main jobs of the combination valve is that it will NOT allow pressure to build-up in the front calipers until AFTER the rear shoes are expanded against the drums.

Add-on; even though their is no longer a residual valve in the MC, their is still a residual effect. Their must be for drum brakes in order to keep the cups expanded, and keep air out,, except that instead of a valve in the MC that job is now part of the combination valve.
The combination valve does a "combination" of things;
1, it operates the failure light.
2, it holds a little pressure in the rear drums.
3, it "holds back" pressure to the front discs until the rear line pressure builds up to a pre-determined level.
4, it limits rear line pressure so the rears don't go into "instant lock-up" before the fronts have a chance to "catch up", as the drums have a large servo effect and require much less pressure to operate.
Discs do not have a "little" servo effect, they have ZERO servo effect.
 

Pinger

I'm Awesome
Joined
Mar 10, 2020
Messages
3,013
Reaction score
5,934
Location
Scotland.
Discs do not have a "little" servo effect, they have ZERO servo effect.

Not so.
There is moment because the friction force and the retaining forces on the pad are offset by the depth of the pad's friction material which causes the pad to be pulled toward the disc. It is slight but not zero.
 

Ryan cin

Newbie
Joined
Nov 24, 2020
Messages
40
Reaction score
41
Location
Ny
Folks have a defective QTU master cylinder, they "upgrade" to a fully-functional non-QTU master from a newer vehicle, and the brakes improve. IT'S MAGIC! I DISCOVERED A MAGIC UPGRADE!. 'Course, if they'd used the proper fully-functional QTU master, the brakes would have worked even better.

Finally, someone who agrees. Seems like the crazy effectiveness of this "upgrade" is just solving all of the problems with a worn-out master cylinder after 200xxx miles.
 
Top