How to: 95-98 OBS and 99-02 NBS Steering Wheel Audio Control Install

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

88GMCtruck

I'm all 8-Luggy!
Joined
Apr 14, 2010
Messages
4,804
Reaction score
1,322
Location
Auburn, Wa: From Covington, Wa: Albion, Wa: Pullma
Here is an install of steering wheel audio controls I did on my 2002 Sierra, and subsequently my old roommates 95 Silverado. It requires very minimal parts surprisingly. The procedures for both the OBS and NBS trucks are VERY similar, and most pictures of my NBS.

Parts:
- Audio Controls & Steering Wheel trim (you can buy the buttons and steering wheel trim from GM separately or just find a Denali/Escalade/Blazer/Jimmy/Bravada Steering Wheel) Also note that the controls come in both grey and black. Both grey and black were used in the S-Series trucks, while only black was used in Denali and Escalades.
- Denali SIR Clockspring Part # 26087300
- Misc Wire
- PAC adapter (if you have an aftermarket stereo)\
- NOTE: If you have an OBS, 98 was the only year with the correct steering wheel. If you have a 95-97 or a higher GVWR truck with no airbag, you will need a new steering wheel and airbag. For higher GVWR trucks without an airbag, the SIR coil will still be required, however the airbag function of it will remain disconnected.


Tools:
- Steering Wheel puller
- Small flat screwdriver
- Torx bits
- The usual wiring "stuff"

Start by disconnecting your battery AND pulling the airbag fuse un the door jamb. THIS IS IMPORTANT. Let the truck sit for 15+ mins to allow for the electrical system to discharge. You don't want your airbag to go off in your face!


Start by first removing the dash bezel and lower dash panel. Under the lower dash panel also remove the metal shield with a 10MM socket. You'll need these out of the way part way into the project (found that out the hard way)

Now, removing the airbag. There are two small openings in the back, use a small screwdriver to release the clips holding it in. You'll figure it out after awhile.
You must be registered for see images attach



Once the bag is released, unclip the electrical connector and carefully set the bag aside. Un-hook your horn wire (red) by turning counter clockwise. Then take the steering wheel puller and remove the wheel.
You must be registered for see images attach



Now your wheel is gone and you have this left.
You must be registered for see images attach


Now take the cover off the column by simply pulling it apart (I think older models had torx screws). You’ll also have to unclip the tilt lever (I think I used a small screwdriver on this too). No you are going to take the old SIR coil out of the column (the black thing with the airbag wire) and unhook it under the dash. You’ll have to cut some zip-ties and such. Take the new SIR coil and route the new wires and plug it all in. NOTE: If you have a 95-97 OBS, you will have to cut the airbag plug off your new coil and swap it from your old coil.
OBS plug splice
You must be registered for see images attach


Route the new 4 wire plug for the audio controls where you can easily work on it later. Now, If you have a new SIR coil, follow the GM instructions that came with it and install it on the column. If you have a used coil, be sure it is centered on the column and you can see the orange thing in the window indicating it's centered. If you don’t install it correctly it will become damaged and your air bag will not function, along with your horn and new radio controls.
OBS
You must be registered for see images attach


NBS
You must be registered for see images attach



Now move on to your steering wheel. If you bought a complete Denali/Escalade/Jimmy wheel and want to keep your factory wheel like I did (mines factory yellow, plus the Denali one I bought was very light grey) You will have to remove the controls and trim cover from the back, the re-install on your existing wheel. These all take torx bits. The back trim piece will also need painted if it doesn't match your interior color.
You must be registered for see images attach



Put the trim back on the column, and then install the steering wheel. Install is reverse of removal. Be sure you plug your airbag back in, and it just pushes back onto the wheel.
OBS
You must be registered for see images attach

You must be registered for see images attach


NBS
You must be registered for see images attach

You must be registered for see images attach



At this point you can re-connect your battery and put your airbag fuse back. Before going any further test for proper horn and airbag functioning. I suggest standing out of the truck the first time you start it. You can also (while still standing outside) cycle the wheels back and forth to make sure your SIR coil is installed correctly.


If the airbag light is off and it didn't deploy, you’re ready to hook the controls up!


Wiring Info:

1. Cut the plug from the SIR coil and connect 4 wires to it, long enough to run to your stereo. I used OEM colors for simplicity.

At the clockspring:
Black - Ground
Grey - Dash light dimmer +12v
Green - Keyed power
Yellow - Data wire

At the radio connector:
Pin 5 – Black – Ground
Pin 7 – Grey – Dash Lights +12v
Pin 9 – Dk Green – Keyed +12v
Pin 14 – EMPTY - Remote Radio Control

2. Splice your ground, power and lights into your radio harness wiring however you choose. The Yellow signal wire goes to a pin in the radio plug that is empty. I shoved it in the socket and taped it in.


Test out your new controls!!! If everything is wired correctly, the controls will do what they say on them (consequently, if they aren't they will do other things, such as not work or change channels with the mute switch). Be sure to check them at night to see if the backlighting works as well!!!
 

mjleg

Ya...I Like Trucks
Joined
Apr 18, 2010
Messages
188
Reaction score
15
Great Write Up, Might give this a try.
 

frito-bandito

8 Lugs + 6 Tires + 4 Doors
Joined
Jun 25, 2010
Messages
7,621
Reaction score
6,567
Location
Simpsonville, SC
Ok I wasn't sure if that was the main part of the contols or not, thanks!

About how much would a SIR coil cost, and would it be smart to get one out of the junkyard if the airbag hasn't deployed?
 
Top