Search results

  1. B

    HD Headlight Harnesses w/ 4 High Mod

    Do you make one for just the fog lights? I have the switch and pigtail just don’t have the time to make the harness.
  2. B

    C3500 SRW Front levelling

    2” coil spacers to level my c2500. Needed balljoint spacers to correct alignment. Bj spacers aren’t installed yet.
  3. B

    GMT400 2WD Lift Guide.

    If 1500 buy new Upper control arms for a lift. Keeps the angles good and leaves adjustment.
  4. B

    GMT400 2WD Lift Guide.

    Ok I did find a set on their site. Around $550. I might pull the spacers and go for the 1” instead of the 2”. Or a BJ spacer. Wasn’t looking to drop that kind of cash on arms when the truck needs rockers and corners . Damn lol
  5. B

    GMT400 2WD Lift Guide.

    How much were your arms?
  6. B

    GMT400 2WD Lift Guide.

    I can’t seem to find an extended UCA for a 8 lug 2500.
  7. B

    GMT400 2WD Lift Guide.

    I have my camber bolts maxed to get it this far. Even got new bolts with more adjustment installed. 2” coil spacer. I guess ball joint spacers would get me to where it can be aligned? C2500 8lug.
  8. B

    C2500 coil spacers

    I have the uca rolled all the way out to get it like that.
  9. B

    C2500 coil spacers

    Ok so I wanted to level out my 89 c2500 8 lug. Ordered 2” coil spacers and installed them. Checked and made sure the knockouts are out and got new more adjustable camber plates. Problem is the top of the tire still leans in. So my question is, will a bj spacer help? There has to be a way. I...
  10. B

    89 c2500 to k2500

    Manual t case for sure. I’m going for a stand alone engine/trans harness so I would just need to figure the vss wiring and the front diff actuator wiring.
  11. B

    89 c2500 to k2500

    Little backstory here, dad bought the truck in 94. It’s a 89 c2500 they had a service body on it. We swapped out to a regular 8ft bed right away. Now it’s 2020 and I want to swap to 4x4. Looking at getting a rolling k2500 frame and swapping body over. Only thing I’m not sure on is the wiring for...
  12. B

    Hard Shift 1-2 gear

    The one I posted is for 4wd the 2wd most likely looks different. It might be on the drivers or passenger side rear tailshaft of the trans on a 2wd.
  13. B

    Hard Shift 1-2 gear

    Vehicle speed sensors on the transfer case. The autotrak transfer case had 2 of them. Same part #s. If it's a 2wd I'd assume it would be on the tail shaft of the trans.
  14. B

    TBI 4l80e experts needed

    If your doing a 6.0 swap have the computer run the trans and engine. One harness
  15. B

    Hard Shift 1-2 gear

    Had a severe problem with this in a 99 Tahoe. After 2 rebuilt and one used trans we figured it out. It was bad speed sensors. I had my ecm re flashed, new valve body's in the trans's and I added an 1870 eliminator shift kit and none of it worked until I changed the speed sensors.
  16. B

    Th-400 to 700r4

    ok I'm sick of not having OD in my 89 c2500. I know a 4l80 would be better but I'm not dropping the money on a stand alone computer. I have a lead on a rebuilt 700 with 22k on it. What all do I need to put this in my truck? I know i need a new driveshaft, wiring is what's got me. I know my...
  17. B

    vortec starter swap

    Yea I didn't know I needed the bolts when I first tried it, literally bolted it up hit the key and it ground and I took it back off. Then I stumbled across one of your posts and orderd the correct ones. Been great for over a year now.
  18. B

    vortec starter swap

    Follow up to this. The vortec starter works. Just had to order the correct mounting bolts!
  19. B

    Post your lifted 2wd's!

    What fabtech spindles did you use? Last set I looked up were discontinued for the 88-89 c2500 Edit. Forget it I just realized you are 6 lug.
  20. B

    88GMCtruck's 98 Silverado Towpig Build: "Black Fox"

    Those aren't bad at all. I struggled fitting full size mini H1 into the stock housing. Yours fit a lot better.
  21. B

    GMT400 Parts (Junkyard Stuff)

    Any 88-94 fog light switches with pigtail? And any 91 clusters with tach?
  22. B

    1989TBI to 04 SS swap questions

    Did you ever attempt the swap?
  23. B

    Blower motor question

    i have a 89 c2500 Scottsdale. I have the 3 speed blower motor now. I'd like to get the 90-94 ac controls that have a multi speed blower. Is that possible? I have the digital display now. Would it be a matter of a new display and a blower motor resistor? I used to have non pulse wipers but all I...
  24. B

    5.3 swap into 92 2500

    IMO a 5.3 is would be good in a 2500. A small cam and it makes more power than the 5.7. However a 6.0 would be ideal.
  25. B

    tj98gmc 98 gmc build thread

    What ever happened to this??

Latest posts

Members online

... and 3 more.
Total: 1,410 (members: 53, guests: 1,357)

Forum statistics

Threads
64,249
Messages
1,389,877
Members
51,243
Latest member
TruckinAnissa707

Share this page

Top