Search results

  1. 93yukon

    Tbi problem

    It's funny because I have a fluke multimeter but only really use it to test voltages to test if things are getting power. checking resistances and looking for voltages drops are my down fall lol
  2. 93yukon

    Tbi problem

    Awesome thanks for the help I'll look into it all tomorrow hopefully. It's about to storm really hard here and I don't want to end up caught out in it lol I really appreciate the help I'm just lost when it comes to electrical Gremlins. I can turn plenty of bolts and nuts but when it comes to...
  3. 93yukon

    Tbi problem

    Which connections besides the distributor connections should I look into? Any others?
  4. 93yukon

    Tbi problem

    Fuel is good it's running 12 +- at the tbi after a fuel filter change I did this morning. So should I do as I asked take and clean connections on the dizzy and dielectric grease them to see if that is the cause first and foremost? Or could it be my plug wires arcing somewhere maybe?
  5. 93yukon

    Tbi problem

    I'll also recheck fuel pressure at the throttle body while I'm in there.
  6. 93yukon

    Tbi problem

    Not to sound like a dummy but what is emi? What can I do to fix the hei shielding and open ground circuit 453? I will go out and clean both connections on the distributor today and put some dielectric grease on them. I have a whole other dizzy that was working when pulled should I swap over the...
  7. 93yukon

    Tbi problem

    So I'm having problems with my tbi as stated above. It's been giving me some problems starting. It's intermittent. It's not fuel related as it's running 8psi. I tried starting it today and when I turned it to key on engine off the tachometer jumped all over the place and while trying to start it...
  8. 93yukon

    Passenger Bucket seat wont stay latched

    Having a problem with my seat is there anyone who can give me some guidance? It's a 93 yukon manual seats. I pulled the bottom part of the lever up and foward to slide the seat foward and seat back foward and now it will not latch and let me adjust my seat back...the seat back just swings...
  9. 93yukon

    92-94 does anyone have this?!?!

    I want to see it lit at night...
  10. 93yukon

    92-94 does anyone have this?!?!

    Nu image wg 103 would really love some pics of it lit up at night...please??
  11. 93yukon

    Driveline slop

    Thanks for the hint!!
  12. 93yukon

    Driveline slop

    Thanks for the info and such it's greatly appreciated!!
  13. 93yukon

    Driveline slop

    Is there difference between the new venture and new process 241?
  14. 93yukon

    Driveline slop

    Which is none of these cases (np241)
  15. 93yukon

    Coolant temp sensor question.

    Yeah you would think....I'm not sure what the problem could be
  16. 93yukon

    Coolant temp sensor question.

    Does it have full coolant? Sounds like the coolant temp sensor to the gauge is like mine it hits 150ish and stops And very well could be about the blend door actuators both being stuck in worked on a Ford pick up that had that problem just last week
  17. 93yukon

    Driveline slop

    It's just good quality insurance
  18. 93yukon

    Driveline slop

    I still wouldn't rule them out yet...I'm planning on getting a full set and redoing them front to back as they are cheap enough to buy...that and I'm getting a vice so I can replace them hahaha
  19. 93yukon

    Driveline slop

    Now my next dilemma is the part # you gave me. I'm not sure we have the same transfer case...I don't know what I have but it's a floor shift mated to a 4l60e. I tried looking it up by my rpo codes but didn't have anything listed as a transfer case as any of my codes. where can I find the case...
  20. 93yukon

    Driveline slop

    Nylon dots? You mean the Nylon factory retainers that you have to melt out? Nope don't have those...they are clipped...
  21. 93yukon

    Driveline slop

    I know I have sockets and such big enough...what year and model is your truck? I just am not sure which bushing I'll need and size output shaft I have whether it's 27 or 31 spline and if mine is the same or not as ypurs
  22. 93yukon

    Driveline slop

    Cool thanks!! Will I have to reseal the tail shaft housing?
  23. 93yukon

    Driveline slop

    If you please would dig me up the bushing part number I'd be thrilled! what does it take to replace that bushing? tail shaft housing removal? will I need other seals etc? I have never taken a transfer case apart so I have no idea what is entangled in doing that job.
  24. 93yukon

    Driveline slop

    What grease should I use on the slip? Lithium or moly? I have seen like 4 or five different opinions.
  25. 93yukon

    Driveline slop

    Thanks!!! I was thinking it could be the bushing I'll have to pull it apart this weekend and check it out to see what's up. I plan on replacing all 4 u joints at some point. My only problem is I don't have a vice so it isn't going to be easy.

Latest posts

Staff online

Members online

... and 10 more.
Total: 1,591 (members: 60, guests: 1,531)

Forum statistics

Threads
64,242
Messages
1,389,527
Members
51,215
Latest member
KScott

Share this page

Top