Search results

  1. E

    1994 k3500 frame.

    Anyone know a rough number on what an extended cab long bed frame might weigh? No rear suspension. Will have the front suspension in place. The frame needs to be moved into the back yard for space. Was wondering if a couple of guys could carry in back there.
  2. E

    Air conditioning box.

    My 98 ext cab has that rear AC under the carpet. I hate it. The truck is currently in storage until I can get onto it as my next project. If I swap out the lower part from a reg cab will it swap? Or am I going to have to swap the whole box over? Anyone tried this or think it’ll work? Without...
  3. E

    Parting out 97 k3500 W/T

    Got a complete truck in the Central Valley CA 95351 I’m keeping anything to do with the trans for my swap. So column and cluster clutch pedal etc. Looking to sell the rest Utility bed 500 W/T grill and lights 200 Dash 300** looks clean Engine is Vortec 454 looking for **SOLD*** And whatever...
  4. E

    1993/4 4l80e VSS

    Does anyone know what the output signal is on the 80e? The trucks a 93 but has 94 parts in her. so I’m curious what the TOSS signal should be? Also does anyone know what the output signal would be on a np261 from a 2002 Silverado? I’m thinking the 80e from the 93/4 should be 2k ppm And the np261...
  5. E

    Speedometer TS

    Alright guys. I have a 93 k3500 eclb dually. It’s got a 94 6.5 TD setup in it. My issues are with the speedometer. All fuses appear to be ok. I have power going to the VSSB as well as VSS output signal from the trans TO the VSSB. idling my speedo output is .09VDC Not sure is that should be read...
  6. E

    For your consideration

    We have two clutch pedal assemblies. One for the 94down and one for the 95.5+ Asking 150 each one comes with a new master And the other is how I pulled it. also have 3 DIC assemblies. two come with the pigtail and functioned when removed. the third one no pigtail. Buttons are sticking...
  7. E

    Borg 4401 to np261

    I have a 1993 6.5TD with the 4l80e/4401 Hello all looking to swap out my 4401( PO kept it) I have an NP261 here and an NV4500 First things first before the overhaul. I wanna test out the engine I recently got running. So my plan is to throw the 261 behind the 4l80e I have sitting here. My...
  8. E

    1993 6.5 TD

    Hey fellas. I picked up a 93 TD that apparently had an engine swap. The diesel in it has the PMD injector pump. DS4 I believe. I have never heard this thing run so for all I know it’s been placed there in a non running condition. My plan is to try and make this thing run and have a unique...
  9. E

    Well... clutch assy needed

    I have a 93ish one ( clutch pedal assy)painted and prepped. I’m looking for the 96+ version. willing to trade or buy one. Lemme know if anyone is interested.
  10. E

    96 suburban emissions thingy?

    does anyone know if this is supposed to be open to atmosphere?
  11. E

    Passanger Drop 241

    hello fellows Was going to swap this into my SAS 98 Silverado Currently have a divorced 205 I was having issues with... got that sorted now I have a pertty gewd NP241 passanger stop from a 91 suburban. I don’t know what y’all wanna pay I got scalped at 500 cuz I “needed” it But I’m...
  12. E

    Starter delay?

    Drove the truck for about 150 miles and then the truck gave me a log pause when turning the key before starting the motor. Then drove it 150 miles back Got gas and it would click no start... I checked EVERYTHING . Put it in n rolled it around a bit put it in park no start. N no start. Pushed...
  13. E

    1996 suburban GMC alarm assistance

    hey fellas Stuck on the wiring for this 10 pin can someone point me in the right direction please? Where do these bad boys go I think I’m too close to the situation and too frustrated
  14. E

    HELLLLLLLPPPPP!!!!!

    hey peeps Installed my remote start the other day then I seen the cool smart start module so I bought it Issue is I need a dealer to activate it Anyone have access? It's all wired in and bla bla Just need a dealer to activate it HMU if you need some munnies
  15. E

    1996 Suburban alt question

    Howdy Fellas My Burb voltage gauge read 12V most of the time Alt woulf drop a few volts here and there battery light would come on I measured the battery and sure enough it measures 12v while truck was running So I swapped out the alt New one reads 14V at the battery while running All good...
  16. E

    Building up an LS1 for the SAS

    Aaaaaand so far not so good Folded a Hf 2 Ton hoist NO problems Only lifted the dressed motor Out of the back of the truck
  17. E

    What are these wires for?

    1997 suburban 5.7 Might have nicked some wires in this loom behind the radio What do you folks recon they do?
  18. E

    93 clutch pedal help

    Can anyone sell me or donate for a few days the bolt bushings, spacers spring etc that holds the pedal to the bracket!? Mine either never came with them or I lost them over the years But if you wanna sell I wanna buy But if you want it back I can machine out a copy for myself PLEASE and THANK YOU
  19. E

    C1500 Front Springs

    Hi there Can anyone give me the ID on these the OD and maybe the height uncompressed and the rate? Thanks guys
  20. E

    Flywheel

    annyone have one they wanna ship to 95354? looking for a flywheel from our trucks fr a manual trans
  21. E

    Advance adapters 50-0405e

    This is to swap the later 4l60e to the np208 mating surface Also has vss parts http://m.ebay.ca/itm/261876086887 Taking first offers from gmt400 members
  22. E

    Kodiak

    https://modesto.craigslist.org/cto/4860034628.html
  23. E

    98 Vortec 5.0 oil pressure

    So I'm getting the red check Gauges warning When I see the warnings pressure isnt registering A quick pop into N makes it pick up Sensor? Oil pump? Odo says 180k I've had her since 100k And only a head gasket job Oils at about four months old And maybe 1500 miles Don't...
  24. E

    Modesto 99z71

    https://modesto.craigslist.org/cto/4896628961.html
  25. E

    Vortec 305 to 350 swap

    Hey guys is this worth it? I'm looking at a crate motor It's currently on a 93 so has the TBI set up But it's a vortec generation motor Is it worth it to pick it up and put it in place of my 305? Or hold off for the 5.3? I'm hoping the heads are correct but im assuming they might be...

Latest posts

Members online

... and 5 more.
Total: 1,562 (members: 55, guests: 1,507)

Forum statistics

Threads
64,336
Messages
1,391,517
Members
51,441
Latest member
omcvay

Share this page

Top