Recent content by OverDrive

Headlights won't turn off...

NP, and sorry I forgot to mention that the dash light will remain on, but i just ignore it lol.
- OverDrive
- Post #9
- May 2, 2017
- Forum: Audio + Electronics
Headlights won't turn off...

If you don't want to have day time running lights, you can pull fuse 15 i believe in the fusebox in the cab. Without it, the headlights only turn on when you have the switched flipped to the vertical position.
- OverDrive
- Post #5
- May 2, 2017
- Forum: Audio + Electronics
Np241 c jumps to neutral

I'm not sure if this is a thing that just goes out on the NP241's, but just in case, you can always check to see if your detent spring is screwed up. Heres a pic of the spring, cap, and plug thing. Its pretty obvious where it is on the bottom of the T-case. Almost looks like a drain plug. Also...
- OverDrive
- Post #3
- Feb 9, 2017
- Forum: Transfer Cases
Post YOUR Favorite Picture of YOUR Truck!!!

Sweet! I've passed through there a couple times.
- OverDrive
- Post #1,493
- Feb 3, 2017
- Forum: Car / Truck Photos and Videos
Post YOUR Favorite Picture of YOUR Truck!!!

Thanks. It sure does lol. I didn't know it before, but there seems to be a fair amount of people from around here on this forum, which is pretty cool.
- OverDrive
- Post #1,491
- Feb 3, 2017
- Forum: Car / Truck Photos and Videos
Post YOUR Favorite Picture of YOUR Truck!!!

Took this picture a while ago after i put on my tow mirrors.
- OverDrive
- Post #1,482
- Jan 31, 2017
- Forum: Car / Truck Photos and Videos
Lower front valance removal

I removed my lower valance months ago, and i've yet to have any over heating problems. Also doesn't seem like it would move any air around at all, but that is just what it would seem like to me.
- OverDrive
- Post #2
- Jan 31, 2017
- Forum: Paint / Body / Detailing
Flowmaster 40 vs 44? Poll!

I don't know about the 44's, but i got a 40 dual in dual out on my truck and it sounds real nice. No drones at cruising speed, pretty loud, and has a good rumble. Here is a pretty bad clip, only revved it up to like 3500 RPM.
- OverDrive
- Post #10
- Jan 20, 2017
- Forum: The Garage
Np241c tailshaft question

If I remember correctly, the tailshaft bolts wont line up if its not oriented correctly. So if all the bolts are tightened down it should be on right lol. I know from spending a good couple minutes spinning the thing around trying to find the right way to bolt it up.:rofl:
- OverDrive
- Post #2
- Dec 16, 2016
- Forum: Engine Performance + Maintenance
Post YOUR Favorite Picture of YOUR Truck!!!

Thanks its a K2500 RCLB, 5.7 Vortec(crate motor that only has 5k miles on it), 4L80E, and a 3.73 rear end. I've already got rid of the old bulky muffler and replaced it with a Flowmaster 40 series, and also replaced old aftermarket drop bumper with a clean 10" drop luverne bumper, otherwise...
- OverDrive
- Post #1,441
- Dec 11, 2016
- Forum: Car / Truck Photos and Videos
Post YOUR Favorite Picture of YOUR Truck!!!

I don't take many pictures of my K2500, but this has to be by far my favorite. Also its cool to hear that some of you guys are also from around Sioux City. I live in Woodbury county.
- OverDrive
- Post #1,439
- Dec 11, 2016
- Forum: Car / Truck Photos and Videos