Recent content by munrom77

  1. M

    Code 41 coming up

    Hello all, Finally got rid of the monies gauges on my 90 5.7 step side truck and now I’m able to get codes out of the truck via blink code. That being said I’m looking at code 41 cam sensor circuit fault, igntion control circuit fault and tried to do a bit of digging into it have not really...
  2. M

    88-91 to 92-94 cluster upgrade

    Hello all, I am wanting to swap out my moonies the cluster itself is starting to fail, having over 500,000km on it I figure it’s time for replacement. I have 2 gauges from the 92-94 sitting in my shop and have connectors, I still have the drac to remove but that is minor. Right now I’m...
  3. M

    Restore of a rcss

    Here are finally some more pictures of the truck, let me know if anyone else wants to see anything else. Or have any questions. Sent from my iPhone using Tapatalk
  4. M

    Restore of a rcss

    As soon as I can get back from work during the day light I will get some more pictures inside and out for you. As for the engine it’s just a 350 that I resealed, reringed and new bearings, the block itself was is in great shape just honed out the block. Sent from my iPhone using Tapatalk
  5. M

    Restore of a rcss

    Well it’s been a long time coming but it’s almost complete, just needs to get the ac charged up I’ll do that later date at work and get an alignment in the next week or or but it’s ready to roll seems to be running good and if I do say so my self looks pretty good also. Sent from my iPhone...
  6. M

    Getting stuff ready for primer and paint

    You don’t think the clear on the bed line will make it too slick? I’m about at the point to finish the top side of my box and do thyou bed liner. I sprayed the bottoms of the doors and rockers of the cab in rockguard and paint and clear and the finish is very slick to run your hand across I’m...
  7. M

    90 350 service engine soon flashing while running

    I believe I may have found the possible issue, with the flashing. It was doing so very faintly. I figured I would try putting a battery charger on it. With the charger it now stays on solid so I’ll let it charge for a while and see what happens, I do believe I will be getting that adapter...
  8. M

    90 350 service engine soon flashing while running

    I don’t have one from the back of the head to the fire wall, I do have one front block to the battery, I’ll add another ground to the back of the head to the fire wall see if that changes anything also Sent from my iPhone using Tapatalk
  9. M

    90 350 service engine soon flashing while running

    Catalyst? I assume you mean cat converter? This truck doesn’t have it and is not required to have it, it has stock manifolds (new) new y pipe, 3 in to the muffler and dual 2.5 out to the tail pipes Sent from my iPhone using Tapatalk
  10. M

    90 350 service engine soon flashing while running

    All grounds are all new for battery to block ,battery to cab, frame to cab, battery to frame. I will check all the grounds at the thermostat and double check my work and am looking for a scan tool that has obd1 ability all of mine that I have are not able to do obd1 Sent from my iPhone using...
  11. M

    90 350 service engine soon flashing while running

    So I tried to get blink codes this morning again after the 3 1-2 combo I got 5-1-4-1-3 and the three really faded out that you could just see it and have good 12.6 volts when doing it Sent from my iPhone using Tapatalk
  12. M

    90 350 service engine soon flashing while running

    It’s a 1990 gmc k1500 with a stock 350 Sent from my iPhone using Tapatalk
  13. M

    90 350 service engine soon flashing while running

    Hello all, Little but stumped right now with my truck, I recently installed a freshened up 350 has 150 compression across the board, has all new sensors and plugs wires etc, Recently set my timing with the wire unplugged to 0 or very close to it, shut down the truck plugged the wire back in...
  14. M

    Wiring

    Here you go Sent from my iPad using Tapatalk
  15. M

    Full fuel line replacement! What would you do?

    It’s a pain to do the ends but I went with nylon fuel lines Sent from my iPhone using Tapatalk
See more

Latest posts

Staff online

Members online

... and 12 more.
Total: 1,768 (members: 62, guests: 1,706)

Forum statistics

Threads
64,249
Messages
1,389,849
Members
51,240
Latest member
Baelfor

Share this page

Top