Recent content by lamogo33

  1. lamogo33

    How soon should I paint? Should I EVEN paint?

    Ultimately the decision is yours to make. When I tell someone it is not worth putting money in to I am trying to impart wisdom rather than give them orders. In some cases it is just better to find a different truck to start with, that will save you money in the long run, perhaps that is all...
  2. lamogo33

    Procedure for minor surface rust?

    Just make Just make sure it is completly sanded off and it won't come back. Then some good primer. Some will suggest using an epoxy primer for a direct to metal (DTM) application but I use 2K stuff usually and don't have issues. See ya! EDIT: And as noted previously, if the bed rails don't...
  3. lamogo33

    454 Vortec head much better than older 454 truck head??

    As stated previously, it would help if you gave everyone a little bit more information to help you. What heads are you comparing them to, and what era of short block? Mark IV, or Gen V, or ....? BTW, I run a 600 on my stock Gen V BBC with out any issue. My truck doesn't rev past 4,500-5,000 and...
  4. lamogo33

    Procedure for minor surface rust?

    Pictures would be helpful. If it is just some surface rust from like scratched-off paint then just hit it with 80 grit sand paper and make sure you have removed it all from the surface then primer over it. Then prep it for paint.
  5. lamogo33

    454 Vortec head much better than older 454 truck head??

    The short answer to your question is no. The Vortec heads I have of my Gen VI is a typical oval port style head. And I believe they are a 112cc head because of the chamber design. I am not an engine guy at all, but I can tell you that those heads are not a power adder like a SBC version. I'd...
  6. lamogo33

    Engine swap

    Bell housing to bell housing it is a direct swap. GM engineering has blessed us that way. L6, SBC, BBC, and even modern LS engines all use the same bell housing bolt pattern.
  7. lamogo33

    New Guy here with a 95 GMC Sierra

    Welcome to the forum. Can you determine if it is coming from the front or rear at least? I'd suspect worn brakes as previously stated. Could also be a differential or wheel/axle bearing but those issues usually make a whining/howl sound.
  8. lamogo33

    Ran fine, 15 mins later No Start. It Cranks, has Fuel Pressure and Spark.[SOLVED]

    Have you replaced the sensor? Although that does look like the issue, I've learned that disconnecting one sensor can put the computer in limp mode, which is actually masking the issue from another sensor. Example: Had a truck fail to start at a gas station, 300 miles from home. Was running rich...
  9. lamogo33

    Ran fine, 15 mins later No Start. It Cranks, has Fuel Pressure and Spark.[SOLVED]

    That is a possibility. I believe the Pssskey came out on these trucks in 98. Someone else will have to chime in who knows them better.
  10. lamogo33

    I need ideas.

    Is it made for our chassis? Almost looks like it bolts up to the holes for the original tow hooks. But TBH I have no idea.
  11. lamogo33

    Do any of you drive junk????

    I do! I was looking for 4L80e and came across one in town. It was rebuilt and the guy wants $300 for it. I told him to keep it, since rebuilt transmissions never last as long as a factory one. A lot of engines are the same way. OEM environments are almost completely dust free and made by robots...
  12. lamogo33

    Seeking Suggestions on my 454 Swap

    That does sound like a lot of work. I hope just repining my current harness will solve it for now. Sorry about it going south on ya. Might be picking your brain later if I continue to have problems. See ya!
  13. lamogo33

    Seeking Suggestions on my 454 Swap

    Thanks! I came across that thread yesterday and have printed it out and have studied it. This morning I purchased new red/blue connectors and the adapter for the IAC. As soon as the arrive I'll dig into it. :) BTW is your truck a 700R4 truck? If so did you get the TCC lockup to work with the...
  14. lamogo33

    Seeking Suggestions on my 454 Swap

    I believe I found a possible solution. It appears I can repin my 92 harness to work with the 94 computer. That is what I'm going to try to do. Thanks.
Top